8501 Electric motors and generators (excluding generating sets)

8501.10 Electric motors; of an output not exceeding 37.5W

• Synchronous motors of an output not exceeding 18 W
• 8501.10.10.10 For use in certain types of aircraft4.7%
• 8501.10.10.20 Synchronous motor for a dishwasher with a water flow control mechanism with: a length without axle of 24 mm (+/- 0,3); a diameter of 49,3 mm (+/- 0,3); a rated voltage of 220 V AC or more but not more than 240 V AC; a rated frequency of 50 Hz or more but not more than 60 Hz; an input power of not more than 4 W; a rotation speed of 4rpm or more but not more than 4,8rpm; an output torque of not less than 10kgf/cm4.7%
• 8501.10.10.40 Synchronous hybrid stepper motor with: an output not exceeding 18 W; two phases; a rated current of not more than 2,5 A/phase; a rated voltage of not more than 20 V; with or without a threaded shaft; for use in the manufacture of 3D printers4.7%
• 8501.10.10.50 Linear actuator for automotive electric seat adjustment applications: consisting of a permanently excited DC motor with an integrated gear mechanism and leadscrew; whether brushed or brushless; whether or not with electronic control unit; whether or not with Hall Effect Sensor; with a nominal voltage of 8 V or higher but not higher than 16 V; with a rated output mechanical power not exceeding 20 W, and with a specified temperature range from -40 °C to 160 °C; for use in the manufacture of automotive components for car's seats4.7%
• 8501.10.10.60 Rotary actuator for automotive electric seat adjustment applications: consisting of a permanently excited DC motor with an integrated gear mechanism; whether brushed or brushless; whether or not with electronic control unit; whether or not with Hall Effect Sensor; with a nominal voltage of 8 V or more but not more than 16 V; with a rated output mechanical power not exceeding 35 W, and with a specified temperature range from -40 °C to 160 °C; for use in the manufacture of automotive components for car's seats4.7%
• 8501.10.10.90 Other4.7%
• Other
• Universal AC/DC motors
• 8501.10.91.10 For use in certain types of aircraft2.7%
• 8501.10.91.90 Other2.7%
• AC motors
• 8501.10.93.10 For use in certain types of aircraft2.7%
• 8501.10.93.90 Other2.7%
• DC motors
• 8501.10.99.10 For use in certain types of aircraft2.7%
• Other
• 8501.10.99.20 Worm axis motor for automotive electric seat adjustment applications: consisting of a permanently excited DC motor with a worm wheel; whether brushed or brushless; whether or not with electronic control unit; whether or not with Hall Effect Sensor; with a nominal voltage of 8 V or more but not more than 16 V; with a rated output mechanical power not exceeding 35 W, and with a specified temperature range from -40 °C to 160 °C; for use in the manufacture of automotive components for car's seats2.7%
• 8501.10.99.30 Linear actuator for automotive electric seat adjustment applications: consisting of a permanently excited DC motor with an integrated gear mechanism and leadscrew; whether brushed or brushless; whether or not with electronic control unit; whether or not with Hall Effect Sensor; with a nominal voltage of 8 V or higher but not higher than 16 V; with a rated output mechanical power not exceeding 20 W, and with a specified temperature range from -40 °C to 160 °C; for use in the manufacture of automotive components for car's seats2.7%
• 8501.10.99.40 Rotary actuator for automotive electric seat adjustment applications: consisting of a permanently excited DC motor with an integrated gear mechanism; whether brushed or brushless; whether or not with electronic control unit; whether or not with Hall Effect Sensor; with a nominal voltage of 8 V or more but not more than 16 V; with a rated output mechanical power not exceeding 35 W, and with a specified temperature range from -40 °C to 160 °C; for use in the manufacture of automotive components for car's seats2.7%
• 8501.10.99.50 Electric (DC) motor powering height adjusting with: a rated output mechanical power not exceeding 35 W; frame integration with a length of 156 mm, a height of 59 mm, a thickness of 36 mm and a weight of 500 g; a stall torque of 45 Nm and ultimate torque of 200 Nm; a maximum current of 15 A; no load speed of 7 RPM or more but not more than 10 RPM; a rotation speed of 4 000 RPM or more but not more than 5 600 RPM; a maximum noise level of 42 dB(A); a maximum angular backlash up to 3 degrees, and a 8 tooth pinion module; for use in the manufacture of automotive components for car's seats2.7%
• 8501.10.99.56 DC Motor: with a speed rotation of not more than 7 000 rpm without load; with a nominal voltage of not more than 18 V; with a maximum power of 24 W; for a specific temperature range from -40°C to 160°C; with or without a gear connection; with or without a mechanical attachment interface; with 2 electrical connections; with a maximum torque of 100 Nm2.7%
• 8501.10.99.58 DC Motor : with a speed rotation of not more than 6500 rpm (without load); with a nominal voltage of 12 V (± 4 V); with a maximal power below than 20 W; with a specified temperature range from -40°C to 160°C; with a worm gear drive; with a mechanical attachment interface; with 2 electrical connections; with a maximum torque of 75 Nm2.7%
• 8501.10.99.60 DC motor: with a rotor speed of 3 500 rpm or more but not more than 5 000 rpm loaded and not more than 6 500 rpm when not loaded; with a power supply voltage of 100 V or more but not more than 240 V; for use in the manufacture of electric fryers2.7%
• 8501.10.99.64 DC motor to control angular position of the flap to adjust gas flow in the Air Throttle and EGR valve: with Ingress Protection (IP) standard of IP69; with a rotor speed of not more than 6 500 rpm when not loaded; with a rated voltage of 12,0 V (± 0,1); of a specified temperature range of - 40 °C or more but not more than 165 °C; with or without a connecting pinion; with or without an engine connector; with or without a flange; with a diameter of not more than 40 mm (not including the flange); with an overall height of not more than 90 mm (from the base to the pinion)2.7%
• 8501.10.99.65 Electric turbocharger actuator, with: a DC motor; an integrated gear mechanism; a (pulling)force of 200 N or more at a minimum of 140°C elevated ambient temperature; a (pulling) force of 250 N or more in each position of its stroke; an effective stroke of 15 mm or more but not more than 25 mm; with or without an on-board diagnostics interface2.7%
• 8501.10.99.70 DC stepping motor, with: a two-phase winding; a rated voltage of 9 V or more, but not more than 16,0 V; of a specified temperature range covering at least - 40 °C to + 105 °C; with or without connecting pinion; with or without motor drive connector2.7%
• 8501.10.99.75 Permanently excited DC motor with: a multiple-phase winding; an external diameter of 24 mm or more but not more than 38 mm; a rated speed of not more than 12 000 rpm; a power supply voltage of 8 V or more but not more than 27 V; with or without a pulley; with or without a gear wheel2.7%
• 8501.10.99.79 DC motor with brushes and an internal rotor with a three-phase winding, whether or not equipped with a worm or a pinion, of a specified temperature range covering at least - 20°C to + 70°C2.7%
• 8501.10.99.90 Other2.7%

8501.20 Electric motors; universal AC/DC of an output exceeding 37.5W

• 8501.20.00.10 Of an output exceeding 735 W but not exceeding 150 kW, for use in civil aircraft—
• 8501.20.00.20 Of an output of less than 750 W or exceeding 150 kW, for use in certain types of aircraft2.7%
• 8501.20.00.50 Universal AC/DC motor, rotating: with a nominal supply voltage of 230 V; with a power of more than 37,5 W but not more than 2 000 W; with a stator cross-section of 93 mm or more but not more than 103 mm and a thickness of 15 mm or more but not more than 45 mm, and with or without a worm gear, gears or a gearbox; for the production of a torque to a transmission shaft for small domestic appliances2.7%
• 8501.20.00.60 Universal AC/DC motor, rotating: with a nominal supply voltage of 230 V; with a power of more than 37,5 W but not more than 1 200 W; with a stator cross-section of 65 mm or more but not more than 75 mm and a thickness of 15 mm or more but not more than 45 mm, and with or without a worm gear, gears or a gearbox; for the production of a torque to a transmission shaft for small domestic appliances2.7%
• 8501.20.00.70 Universal AC/DC motor, rotating: with a nominal supply voltage of 230 V; with a power of more than 37,5 W but not more than 700 W; with a stator cross-section of 49 mm or more but not more than 59 mm and a thickness of 15 mm or more but not more than 45mm, and with or without a worm gear, gears or a gearbox; for the production of a torque to a transmission shaft for small domestic appliances2.7%
• 8501.20.00.90 Other2.7%

8501.31 Electric motors and generators; DC, of an output not exceeding 750W

• 8501.31.00.10 Motors of an output exceeding 735 W, DC generators, for use in civil aircraft—
• 8501.31.00.20 For use in certain types of aircraft2.7%
• Other
• 8501.31.00.45 DC motors, brushless, with: an external diameter of 90 mm or more, but not more than 110 mm; a rated speed of not more than 3 680 rpm; an output of 600 W or more but not more than 740 W at 2 300 rpm and at 80 °C; a supply voltage of 12 V; a torque of not more than 5,67 Nm; a rotor position sensor; an electronic star-point relay, and for use with an electric power steering control module2.7%
• 8501.31.00.47 Motor for automotive electric seat adjustment applications: with a shaft output on both motor sides; consisting of a permanently excited DC motor; whether brushed or brushless; whether or not with electronic control unit; whether or not with Hall Effect Sensor; with a nominal voltage of 8 V or more but not more than 16 V; with a rated output mechanical power not exceeding 120 W, and with a specified temperature range from -40 °C to 160 °C; for use in the manufacture of automotive components for car's seats2.7%
• 8501.31.00.48 Brushless DC electric motors: with a rated power of 240 W or more, but not more than 260 W; with a voltage of 36 V or higher, but not higher than 52 V; with a torque of 20 Nm or more, but not more than 140 Nm; with a housing made of aluminum, aluminum alloy or plastic; with or without a built-in controller; with a communication function in the LIN or UART interface; weighing 1,5 kg or more, but not more than 5,0 kg; adapted for mounting in a bicycle frame; for use in the manufacture of e-bikes2.7%
• 8501.31.00.49 Brushless DC electric motors: with a rated power of 240 W or more, but not more than 260 W; with a voltage of 24 V or higher, but not higher than 52 V; with a torque of 30 Nm or more, but not more than 62 Nm; with a LIN, UART or CAN communication interface; with an internal planetary gearbox with fixed or variable ratio or direct drive; with a housing made of aluminum or aluminium alloy; with a weight of 1,5kg or more, but not more than 6kg; adapted for mounting in the front or rear bicycle wheel; for use in the manufacture of e-bikes2.7%
• 8501.31.00.50 DC motors, brushless, with: an external diameter of 80 mm or more, but not more than 200 mm; a supply voltage of 4 V or more, but not more than 16 V; an output at 20 °C of 200 W or more, but not more than 750 W; a torque at 20 °C of 2,00 Nm or more, but not more than 7,00 Nm; a rated speed at 20 °C of 600 rpm or more, but not more than 3 100 rpm; with or without a pulley; with or without an electronic power steering sensor/controller2.7%
• 8501.31.00.52 Electric brushless direct current motor finished with biocompatible materials such as stainless steel according to specification 17-4 PH or type 303, 316L, 400 with: a three-phase winding; an output power not exceeding 280 W; a length with gearhead of 116,1 mm or more but not more than 117,2 mm; an external diameter of 13,86 mm or more but no more than 13,92 mm; a maximum torque of motor with gearhead 246,6 mNm in 25℃; a no-load radial speed of motor with gearhead with 9 900 rpm, at 24V in 25°C; a weight of motor with gearhead of 70,5 g or more but not more than 71,5 g, a resistance to peak temperature of 140°C or more (non-operating), a maximal air leak between shaft and shaft seals of 15 Pa/s at given 2 Bars of pressure; -14 functional pins for power and control purpose: a flexible printed circuit with length of 245 mm but no longer than 255 mm with mounted 8 pin male connector; for use in the manufacture of medical devices with right-left rotation and oscillation function2.7%
• 8501.31.00.54 Brushless DC electric motor, with: a rated voltage of 310 V; a rated power of 350 W or more but not more than 368 W; an input power of 500 W or more but not more than 550 W; output power of 350 W or more but not more than 400 W; an external diameter without bracket connector and pulley of 143,2 mm or more but not more than 143,8 mm; a rated speed of 16300 rpm or more but not more than 16500 rpm; a weight of 2,33 kg or more but not more than 2,40 kg; a pulley2.7%
• 8501.31.00.55 DC motor with or without commutator, for driving hand-held power tools, lawn mowers or home appliances, with: an external diameter of 24,2 mm or more, but not more than 140 mm; a rated speed of 3300 rpm or more, but not more than 26200 rpm; a rated supply voltage of 3,6 V or more, but not more than 230 V; an output power of more than 37,5 W , but not more than 2400 W; a free load current of not more than 20,1 A; a maximum efficiency of 50 % or more,2.7%
• 8501.31.00.56 DC motor, brushless, integrated with an Electronic Control Unit (ECU), defined as a Power Pack with: a safety feature and mechanism designed for prevention of critical hazards like self-steer by single failure; a CAN-communication interface; an external sensor interface; operating temperature range of -40℃ to 95℃ or broader; compliance with standard IP6K9K for water and dustproofness; supply voltage of 9 V or more, but not more than 16 V; rated power output of 500 W or more, but not higher than 750 W; rated torque of 3 Nm or more, but not more than 6 Nm; length of 150 mm or more, but not more than 250 mm; width of 100 mm or more, but not more than 150 mm; height of 80 mm or more, but not more than 120 mm2.7%
• 8501.31.00.57 Brushless DC electric motor with LCD control indicator and/or control unit with buttons: with an output power of 200 W or more, but not more than 700 W; with a supply voltage of 30 V or more, but not more than 60 V; with a torque of 30 Nm or more, but not more than 200 Nm; with a height of 117 mm or more, but not more than 146 mm; with a length of 117 mm or more, but not more than 223 mm; with a width of 135 mm or more, but not more than 190 mm; with a weight of 2 kg or more but not more than 5 kg; designed to be mounted in a frame, front or rear bicycle wheel; equipped with sockets, at least for cable connection with LCD control indicator; for use in the manufacture of electric bicycles2.7%
• 8501.31.00.58 Permanently excited DC motor with: an external diameter of 27 mm or more but not more than 90 mm, including mounting flange; a rated speed of not more than 25 000 rpm; an output of 45 W or more but not more than 400 W, and a supply voltage of 9 V or more but not more than 50 V; whether or not a multiple-phase winding; whether or not with a drive disc; whether or not with a crankcase; whether or not with a fan; whether or not with a cap assembly; whether or not with a sun gear; whether or not with a speed and rotational direction encoder; whether or not with or without a speed or rotational direction sensor of resolver type or Hall effect type; whether or not with a mounting flange; for use in the manufacture of air suspension seats in tractors, earthmoving machines and forklifts or for use in the manufacture of actuators for height-adjustable furniture2.7%
• 8501.31.00.63 Ready for installation in vehicles or equipment of headings 8432 and 8433, brushless and permanently excited direct current motor with: a specified speed of not more than 6000rpm; a minimum output of 400W, but not more than 1,3kW (at 12 V), or with a minimum output of 750W but not more than 1,55kW (at 36 V); a flange diameter of 85mm or more but not more than 200mm; a maximum length of 335mm, measured from the beginning of the shaft to the outer ending; a housing length of not more than 265mm, measured from the flange to the outer ending; a maximum of two-piece (basic housing including electric components and flange with minimum 2 and maximum 11 bore holes) aluminium diecast or sheet steel housing whether or not with a sealing compound (groove with an O-ring and grease); a stator with single T-tooth design and single coil windings in 9/6 or 12/8 or 12/10 topology, and surface magnets; whether or not with electronic power steering controller; whether or not with pulley or coupling; whether or not with rotor position sensor2.7%
• 8501.31.00.68 Camshaft actuator for controlling the timing of valve opening by using electromotor in a continuous variable valve timing system of an internal combustion piston engine, of: a length of 110 mm or more but not more than 140 mm; a width of 90 mm or more but not more than 130 mm; a height of 80 mm or more but not more than 110 mm; for use in the manufacture of engines of motor vehicles2.7%
• 8501.31.00.85 Power transmission device for controlling the output of exhaust gas turbochargers, consisting of: a DC motor of an output not exceeding 600 W; for usage with a supply voltage of 8 V or more but no more than 48 V; with motor connection (plug-in connection); whether or not with position sensor; whether or not with integrated control and power electronics; whether or not with spring mechanism for resetting the lever; built in a housing with reduction gear and lever attached to the motor drive shaft, or built in a housing with threads integrated into the rotor of the motor for linear movement of the integrated control rod2.7%
• 8501.31.00.99 Other2.7%

8501.32 Electric motors and generators; DC, of an output exceeding 750W but not exceeding 75kW

• 8501.32.00.10 For use in civil aircraft—
• Other
• 8501.32.00.40 DC motor with or without commutator, for driving hand-held power tools, lawn mowers or home appliances, with: an external diameter of 24,2 mm or more, but not more than 140 mm; a rated speed of 3300 rpm or more, but not more than 26200 rpm; a rated supply voltage of 3,6 V or more, but not more than 230 V; an output power of more than 37,5 W , but not more than 2400 W; a free load current of not more than 20,1 A; a maximum efficiency of 50 % or more,2.7%
• 8501.32.00.65 Ready for installation in vehicles or equipment of headings 8432 and 8433, brushless and permanently excited direct current motor with: a specified speed of not more than 6000rpm; a minimum output of 400W, but not more than 1,3kW (at 12 V), or with a minimum output of 750W but not more than 1,55kW (at 36 V); a flange diameter of 85mm or more but not more than 200mm; a maximum length of 335mm, measured from the beginning of the shaft to the outer ending; a housing length of not more than 265mm, measured from the flange to the outer ending; a maximum of two-piece (basic housing including electric components and flange with minimum 2 and maximum 11 bore holes) aluminium diecast or sheet steel housing whether or not with a sealing compound (groove with an O-ring and grease); a stator with single T-tooth design and single coil windings in 9/6 or 12/8 or 12/10 topology, and surface magnets; whether or not with electronic power steering controller; whether or not with pulley or coupling; whether or not with rotor position sensor2.7%
• 8501.32.00.99 Other2.7%

8501.33 Electric motors and generators; DC, of an output exceeding 75kW but not exceeding 375kW

• 8501.33.10.00 Hydrogen fuel cell generators2.7%
• Other
• 8501.33.90.10 Motors of an output not exceeding 150 kW and generators, for use in civil aircraft—
• 8501.33.90.20 Of an output exceding 150 kW, for use in certain types of aircraft2.7%
• 8501.33.90.30 Electric drive for motor vehicles, with an output of not more than 315 kW: with an AC or DC motor with or without transmission; with or without power electronics2.7%
• 8501.33.90.99 Other2.7%

8501.34 Electric motors and generators; DC, of an output exceeding 375kW

• 8501.34.00.10 Generators for use in civil aircraft—
• 8501.34.00.99 Other2.7%

8501.40 Electric motors; AC motors, single-phase

• Of an output not exceeding 750 W
• 8501.40.20.10 Of an output exceeding 735 W, for use in civil aircraft—
• 8501.40.20.20 For use in certain types of aircraft2.7%
• 8501.40.20.35 Electric AC motor, single-phase, with: a rated power of 120 W or more but not more than 150 W; an input power of 280 W or more but not more than 350 W; an external diameter without bracket connector and pulley of 145 mm or more but not more than 160 mm; a rated speed of 2 680 rpm or more but not more than 3 000 rpm; a weight of 4,2 kg or more but not more than 4,6 kg; pulleys, a spindle and a tachometer; for use in the manufacture of home appliance products2.7%
• 8501.40.20.45 Electric AC motor, single-phase, with: a rated power of 275 W or more, but not more than 325 W; an input power of 600 W or more but not more than 700 W; an external diameter without bracket and connector of 150 mm or more but not more than 170 mm; a rated speed of 15 000 rpm or more but not more than 20 000 rpm; a weight of 4,2 kg or more; a pulley and a tachometer; for use in the manufacture of home appliance products2.7%
• 8501.40.20.50 Electric AC motor, single-phase, with: a rated power of 300 W or more but not more than 370 W; an input power of 600 W or more but not more than 700 W; an external diameter without bracket and connector of 150 mm or more but not more than 170 mm; a rated speed of 15 000 rpm or more but not more than 19 000 rpm; a weight of 4,8 kg or more; a pulley; for use in the manufacture of home appliance products2.7%
• 8501.40.20.55 Electric AC motor, single-phase, with: a rated power of 275 W or more, but not more than 325 W; an input power of 600 W or more but not more than 700 W; an external diameter without bracket and connector of 160 mm or more but not more than 180 mm; a rated speed of 15 000 rpm or more but not more than 19 000 rpm; a weight of not more than 4,4 kg; a pulley; for use in the manufacture of home appliance products2.7%
• 8501.40.20.60 Electric AC motor, single-phase, with: a rated power of 275 W or more but not more than 325 W; an output power of 550 W or more but not more than 600 W; an input power of 800 W or more but not more than 1 000 W; an external diameter of more than 150 mm but not more than 170 mm without the bracket; a rated speed of more than 16 000 rpm but not more than 18 000 rpm; a weight of 3,4 kg or more but not more than 3,7 kg; a pulley; for use in the manufacture of home appliance products2.7%
• 8501.40.20.70 Electric AC motor, single-phase, whether or not with commutator: with a nominal output of 180 W or more; with an input power of 150 W or more but not more than 2 700 W; with an external diameter of more than 44,8 but not more than 135,2 mm; with a rated speed of more than 10 000 rpm but not more than 50 000 rpm; whether or not equipped with air-inducting ventilator; whether or not with mechanical device (pinion, screws, gear connection etc.) on the shaft; for use in the manufacture of domestic appliances2.7%
• 8501.40.20.75 Incomplete, single-phase brushless AC motor consisting of a rotor and a stator: a rotor on the inside is equipped with a ring of 12 magnets housed in a steel casing; a stator with an internal diameter of 206,6 mm (± 0,5 mm), external diameter of 265,0 mm (± 0,2 mm) and width of 37,2 mm or more but not more than 47,8 mm; with a rated power not exceeding 750 W; with a weight of 5 kg or more; for use in the production of washing machines, washer-dryers equipped with a drum with direct drive2.7%
• 8501.40.20.80 Other2.7%
• Of an output exceeding 750 W
• 8501.40.80.10 Of an output not exceeding 150 kW, for use in civil aircraft—
• 8501.40.80.20 Of an output exceeding 150 kW, for use in certain types of aircraft2.7%
• 8501.40.80.50 Electric drive for motor vehicles, with an output of not more than 315 kW: with an AC or DC motor with or without transmission; with or without power electronics2.7%
• 8501.40.80.70 Electric AC motor, single-phase, whether or not with commutator: with a nominal output of 180 W or more; with an input power of 150 W or more but not more than 2 700 W; with an external diameter of more than 44,8 but not more than 135,2 mm; with a rated speed of more than 10 000 rpm but not more than 50 000 rpm; whether or not equipped with air-inducting ventilator; whether or not with mechanical device (pinion, screws, gear connection etc.) on the shaft; for use in the manufacture of domestic appliances2.7%
• 8501.40.80.90 Other2.7%

8501.51 Electric motors; AC motors, multi-phase, of an output not exceeding 750W

• 8501.51.00.10 Of an output exceeding 735 W, for use in civil aircraft—
• 8501.51.00.20 Of an output of less than 750 W, for use in certain types of aircraft2.7%
• 8501.51.00.25 Electric permanent magnet synchronous motor with: an output power of 550 W; a rotor containing 8 poles generated by permanent magnets composed mainly with neodymium-iron-boron (per GB/T 13560 standard) enclosed in polyethylene cover; an outer diameter of motor magnet shaft end with dimension of 10,001 mm or more but no more than 10,007 mm; terminals located across the radius 32,5 mm and separated by an angle of 21,8°; a motor housing made of ADC12 or AC46000 aluminium alloy die casting with composition of aluminium-silicon-copper (per JIS H5302 or EN1706 standard); a back electromotive force constant (Ke) of 0,03306 V-sec/rad or more but no more than 0,03654 V-sec/rad; a back electromotive force harmonic order - 5th of no more than 0,38 % (of fundamental) and 7th of no more than 0,25 % (of fundamental); a cogging torque of no more than 13 mNm; a friction torque in ambient temperature of no more than 22 mNm; a maximum temperature of motor operation of no more than 200 °C2.7%
• 8501.51.00.30 AC synchronous servo motor with resolver and brake for a maximum speed of not more than 6 000rpm,With: an output of 340W or more but not more than 7,4kW; a flange of dimensions of not more than 180mm × 180mm, and a length from flange to extreme end of resolver of not more than 271mm2.7%
• 8501.51.00.35 Electric permanent magnet synchronous motor with: an output power of 600 W; a rotor containing 8 poles generated by permanent magnets composed mainly with neodymium-iron-boron and dysprosium enclosed in aluminium cover; an outer diameter of motor magnet shaft end with dimension of 10,001 mm or more but no more than 10,007 mm; terminals located across the diameter 59,2 mm and separated by an angle 30,0°; a housing made of electrogalvanized steel (per JIS G3313 Grade SECE standard) using a deep-drawing stamping process; a diameter of 88,600 mm or less but no less than 88,546 mm at the motor-system assembly interface; a back electromotive force constant (Ke) of 0,03277 V-sec/rad or more but no more than 0,03623 V-sec/rad; a back electromotive force harmonic order - 5th of no more than 0,35 % (of fundamental) and 7th of no more than 0,30 % (of fundamental); a cogging torque of no more than 12 mNm; a friction torque in ambient temperature of no more than 23 mNm; a maximum temperature of motor operation of no more than 200 °C2.7%
• 8501.51.00.40 Electric AC motor, three-phase, with: a rated power of 280 W or more but not more than 320 W; an output power of 480 W or more but not more than 540 W; an input power of 800 W or more but not more than 900 W; an external diameter of 150 mm or more but not more than 170 mm; a rated speed of 15 000 rpm or more but not more than 20 000 rpm; a weight of 6 kg or more but not more than 6,4 kg; a pulley and a tachometer; for use in the manufacture of home appliance products2.7%
• 8501.51.00.45 Automotive-ready brushless permanently excited magnet synchronous alternating current motor with: a specified speed of not more than 7000 rpm; an output of 400 W or more but not more than 750 W (at 12 V); a flange diameter of 80 mm or more, but not more than 200 mm; a maximum length of not more than 335 mm, measured from the beginning of the shaft to its outer end; a housing length of not more than 265 mm, measured from the flange to the outer end; a steel sheet or die-cast aluminium basic housing consisting of not more than two parts, including electrical components and a flange with two or more but not more than 11 holes, whether or not with a sealing connection (groove with O-ring and protective grease or liquid seal interface); a stator with single T-tooth design and single coil winding with 9/6 or 12/10 or 12/8 topology and surface magnets; whether or not with electronic power steering controller; whether or not with pulley or coupling; whether or not with rotor position sensor2.7%
• 8501.51.00.50 Three phase AC synchronous brushless permanent magnet motor with: an output of 500 W or more but not more than 700 W; an external diameter of 129,7 mm or more but not more than 180,3 mm; a rated speed of 16 000 rpm or more but not more than 17 000 rpm; a weight of 2,5 kg or more but not more than 3,1 kg, and with a pulley; for use in the manufacture of home appliance products2.7%
• 8501.51.00.90 Other2.7%

8501.52 Electric motors; AC motors, multi-phase, of an output exceeding 750W but not exceeding 75kW

• Of an output exceeding 750 W but not exceeding 7,5 kW
• 8501.52.20.10 For use in civil aircraft—
• Other
• 8501.52.20.50 AC synchronous servo motor with resolver and brake for a maximum speed of not more than 6 000rpm,With: an output of 340W or more but not more than 7,4kW; a flange of dimensions of not more than 180mm × 180mm, and a length from flange to extreme end of resolver of not more than 271mm2.7%
• 8501.52.20.55 Brushless synchronous alternating current electric motors with permanent magnets, with: an output power of 1000 W or more, but not more than 1400 W; a rotor containing 8 poles, generated by permanent magnets composed mainly of praseodymium-neodymium-iron-boron (GB/T 13560-2017 standard), enclosed in a stainless steel cover; a motor magnet shaft end outer diameter of 10,001 mm or more, but not more than 10,007 mm; motor terminals located across the 37,00 mm radius and separated by an angle of 30,00 °; a motor housing made of ADC12 or EN AC46000 aluminium alloy die casting with composition of aluminium-silicon-copper (per JIS H5302-2000 or EN 1706 standard); a back electromotive force constant (Ke) of 0,0265 V-sec/rad or more, but not more than 0,0293 V- sec/rad; a back electromotive force (EMF) harmonic order - 5th of no more than 0,4 % (of fundamental) and 7th of no more than 0,2 % (of fundamental); a synchronous inductance of 33,49 µH or more, but not more than 37,01 µH; a cogging torque of not more than 15 mNm; a friction torque in ambient temperature of not more than 20 mNm; a maximum motor operation temperature of not more than 200 °C; with or without a spline on the motor shaft2.7%
• 8501.52.20.70 Automotive-ready brushless permanently excited magnet synchronous alternating current motor with: a specified speed of not more than 7000 rpm; an output of 750 W or more but not more than 1,8 kW (at 12 V); a flange diameter of 80 mm or more, but not more than 200 mm; a maximum length of not more than 335 mm, measured from the beginning of the shaft to its outer end; a housing length of not more than 265 mm, measured from the flange to the outer end; a steel sheet or die-cast aluminium basic housing consisting of not more than two parts, including electrical components and a flange with two or more but not more than 11 holes, whether or not with a sealing connection (groove with O-ring and protective grease or liquid seal interface); a stator with single T-tooth design and single coil winding with 9/6 or 12/10 or 12/8 topology and surface magnets; whether or not with electronic power steering controller; whether or not with pulley or coupling; whether or not with rotor position sensor2.7%
• 8501.52.20.80 Electric permanent magnet synchronous motor with: an output power of 850 W; a rotor containing 8 poles generated by permanent magnets composed mainly with neodymium-iron-boron (per GB/T 13560 standard) enclosed in polyethylene cover; an outer diameter of motor magnet shaft end with dimension of 10,001 mm or more but no more than 10,007 mm; terminals located across the radius 26,2 mm and separated by an angle 30,0°; a housing made of ADC12 or AC46000 aluminium alloy die casting with composition of aluminium-silicon-copper (per JIS H5302 or EN1706 standard) and anodized coating (per ASTM B580 type E standard); a back electromotive force constant (Ke) of 0,04009 V-sec/rad or more but no more than 0,04431 V-sec/rad; a back electromotive force harmonic order - 5th of no more than 0,36 % (of fundamental) and 7th of no more than 0,24 % (of fundamental); a cogging torque of no more than 20 mNm; a friction torque in ambient temperature of no more than 26,5 mNm; a maximum temperature of motor operation of no more than 200 °C2.7%
• 8501.52.20.89 Other2.7%
• Of an output exceeding 7,5 kW but not exceeding 37 kW
• 8501.52.30.10 For use in civil aircraft—
• 8501.52.30.90 Other2.7%
• Of an output exceeding 37 kW but not exceeding 75 kW
• 8501.52.90.10 For use in civil aircraft—
• 8501.52.90.90 Other2.7%

8501.53 Electric motors; AC motors, multi-phase, of an output exceeding 75kW

• Traction motors
• 8501.53.50.10 Electric drive for motor vehicles, with an output of not more than 315 kW: with an AC or DC motor with or without transmission; with or without power electronics2.7%
• 8501.53.50.20 AC traction motor of the Interior Permanent Magnet Synchronous Motor (IPMSM) type with: a torque output of 200 Nm or more, but not more than 400 Nm; a power output of 50 kW or more, but not more than 200 kW; a rotation speed of no more than 15 000 rpm; for use in the manufacture of electric vehicles2.7%
• 8501.53.50.30 Permanent magnet synchronous traction motor, with: a continuous power of 110 kW or more but not more than 180 kW; a liquid cooled system; a total length of 500 mm or more but not more than 650 mm; a total width of 600 mm or more but not more than 700 mm; a total height of 550 mm or more but not more than 650 mm; weighing of not more than 350 kg; -3 suspension points2.7%
• 8501.53.50.40 Permanent magnet traction AC motor, with: a continuous power of 110 kW or more but not more than 150 kW; a liquid cooled system; a total length of 460 mm or more but not more than 590 mm; a total width of 450 mm or more but not more than 580 mm; a total height of 490 mm or more but not more than 590 mm; a weight of not more than 310 kg; -4 mounting points2.7%
• 8501.53.50.50 Asynchronous traction motor, with: a continuous power of 140 kW or more but not more than 180 kW; a liquid cooled system; a total length of 580 mm or more but not more than 730 mm; a total width of 550 mm or more but not more than 670 mm; a total height of 510 mm or more but not more than 630 mm; with a weight of not more than 390 kg; with or without reduction gear; with or without starter generator; -2 mounting points; for use in the manufacture of the electric drive of hybrid buses2.7%
• 8501.53.50.90 Other2.7%
• Other, of an output
• Exceeding 75 kW but not exceeding 375 kW
• 8501.53.81.10 Of an output not exceeding 150 kW, for use in civil aircraft—
• 8501.53.81.20 Of an output exceeding 150 kW, for use in certain types of aircraft2.7%
• 8501.53.81.90 Other2.7%
• Exceeding 375 kW but not exceeding 750 kW
• 8501.53.94.10 For use in certain types of aircraft2.7%
• 8501.53.94.90 Other2.7%
• Exceeding 750 kW
• 8501.53.99.10 For use in certain types of aircrafts2.7%
• 8501.53.99.90 Other2.7%

8501.61 Generators; AC generators, (alternators), other than photovoltaic generators, of an output not exceeding 75kVA

• Of an output not exceeding 7,5 kVA
• 8501.61.20.10 For use in civil aircraft—
• 8501.61.20.90 Other2.7%
• Of an output exceeding 7,5 kVA but not exceeding 75 kVA
• 8501.61.80.10 For use in civil aircraft—
• 8501.61.80.99 Other2.7%

8501.62 Electric generators; AC generators, (alternators), other than photovoltaic generators, of an output exceeding 75kVA but not exceeding 375kVA

• 8501.62.00.10 For use in civil aircraft—
• 8501.62.00.40 AC, 3-phase generator, with: a continuous power of 147 kVA or more but not more than 222 kVA; a continuous torque of 650 Nm or more but not more than 900 Nm; a maximum working speed of 2700 revolutions per minute (rpm); a liquid cooled system; a length of 100 mm or more but not more than 200 mm; a width of 550 mm or more but not more than 650 mm; a height of 550 mm or more but not more than 650 mm; weighing of not more than 150 kg2.7%
• 8501.62.00.98 Other2.7%

8501.63 Electric generators; AC generators, (alternators), other than photovoltaic generators, of an output exceeding 375kVA but not exceeding 750kVA

• 8501.63.00.10 For use in civil aircraft—
• 8501.63.00.99 Other2.7%

8501.64 Electric generators; AC generators, (alternators), other than photovoltaic generators, of an output exceeding 750kVA

• 8501.64.00.00 Of an output exceeding 750 kVA2.7%

8501.71 Electric generators; photovoltaic DC generators, of an output not exceeding 50W

• 8501.71.00.00 Of an output not exceeding 50 W2.7%

8501.72 Electric generators; photovoltaic DC generators, of an output exceeding 50W

• 8501.72.00.00 Of an output exceeding 50 W2.7%

8501.80 Electric generators; (excluding generating sets), photovoltaic AC generators (alternators)

• 8501.80.00.00 Photovoltaic AC generators2.7%