8501 Electric motors and generators (excluding generating sets)

8501.10 Electric motors; of an output not exceeding 37.5W

• Synchronous motors of an output not exceeding 18 w
• 8501.10.10.10 For use in certain types of aircraftFree
• 8501.10.10.20 Synchronous motor for a dishwasher with a water flow control mechanism with - a length without axle of 24 mm (+/- 0,3), - a diameter of 49,3 mm (+/- 0,3) - a rated voltage of 220 v ac or more but not more than 240 v ac, - a rated frequency of 50 hz or more but not more than 60 hz, - an input power of not more than 4 w, - a rotation speed of 4rpm or more but not more than 4,8rpm, - an output torque of not less than 10kgf/cmFree
• 8501.10.10.40 Synchronous hybrid stepper motor with: -an output not exceeding 18 w, -two phases, -a rated current of not more than 2,5 a/phase, -a rated voltage of not more than 20 v, -with or without a threaded shaft, for use in the manufacture of 3d printersFree
• 8501.10.10.50 Linear actuator for automotive electric seat adjustment applications: -consisting of a permanently excited dc motor with an integrated gear mechanism and leadscrew, -whether brushed or brushless, -whether or not with electronic control unit, -whether or not with hall effect sensor, -with a nominal voltage of 8 v or higher but not higher than 16 v, -with a rated output mechanical power not exceeding 20 w, and -with a specified temperature range from -40 °c to 160 °c, for use in the manufacture of automotive components for car's seatsFree
• 8501.10.10.60 Rotary actuator for automotive electric seat adjustment applications: -consisting of a permanently excited dc motor with an integrated gear mechanism, -whether brushed or brushless, -whether or not with electronic control unit, -whether or not with hall effect sensor, -with a nominal voltage of 8 v or more but not more than 16 v, -with a rated output mechanical power not exceeding 35 w, and -with a specified temperature range from -40 °c to 160 °c, for use in the manufacture of automotive components for car's seatsFree
• 8501.10.10.90 OtherFree
• Other
• Universal ac/dc motors
• 8501.10.91.10 For use in certain types of aircraftFree
• 8501.10.91.90 OtherFree
• Ac motors
• 8501.10.93.10 For use in certain types of aircraftFree
• 8501.10.93.90 OtherFree
• Dc motors
• 8501.10.99.10 For use in certain types of aircraftFree
• Other
• 8501.10.99.20 Worm axis motor for automotive electric seat adjustment applications: -consisting of a permanently excited dc motor with a worm wheel, -whether brushed or brushless, -whether or not with electronic control unit, -whether or not with hall effect sensor, -with a nominal voltage of 8 v or more but not more than 16 v, -with a rated output mechanical power not exceeding 35 w, and -with a specified temperature range from -40 °c to 160 °c, for use in the manufacture of automotive components for car's seatsFree
• 8501.10.99.30 Linear actuator for automotive electric seat adjustment applications: -consisting of a permanently excited dc motor with an integrated gear mechanism and leadscrew, -whether brushed or brushless, -whether or not with electronic control unit, -whether or not with hall effect sensor, -with a nominal voltage of 8 v or higher but not higher than 16 v, -with a rated output mechanical power not exceeding 20 w, and -with a specified temperature range from -40 °c to 160 °c, for use in the manufacture of automotive components for car's seatsFree
• 8501.10.99.40 Rotary actuator for automotive electric seat adjustment applications: -consisting of a permanently excited dc motor with an integrated gear mechanism, -whether brushed or brushless, -whether or not with electronic control unit, -whether or not with hall effect sensor, -with a nominal voltage of 8 v or more but not more than 16 v, -with a rated output mechanical power not exceeding 35 w, and -with a specified temperature range from -40 °c to 160 °c, for use in the manufacture of automotive components for car's seatsFree
• 8501.10.99.50 Electric (dc) motor powering height adjusting with: -a rated output mechanical power not exceeding 35 w, -frame integration with a length of 156 mm, a height of 59 mm, a thickness of 36 mm and a weight of 500 g, -a stall torque of 45 nm and ultimate torque of 200 nm, -a maximum current of 15 a, -no load speed of 7 rpm or more but not more than 10 rpm, -a rotation speed of 4 000 rpm or more but not more than 5 600 rpm, -a maximum noise level of 42 db(a), -a maximum angular backlash up to 3 degrees, and -a 8 tooth pinion module, for use in the manufacture of automotive components for car's seatsFree
• 8501.10.99.56 Dc motor: - with a speed rotation of not more than 7 000 rpm without load, - with a nominal voltage of not more than 18 v, - with a maximum power of 24 w, - for a specific temperature range from -40°c to 160°c, - with or without a gear connection, - with or without a mechanical attachment interface, - with 2 electrical connections, - with a maximum torque of 100 nmFree
• 8501.10.99.58 Dc motor : - with a speed rotation of not more than 6500 rpm (without load), - with a nominal voltage of 12 v (± 4 v), - with a maximal power below than 20 w, - with a specified temperature range from -40°c to 160°c, - with a worm gear drive, - with a mechanical attachment interface, - with 2 electrical connections, - with a maximum torque of 75 nmFree
• 8501.10.99.60 Dc motor - with a rotor speed of 3 500 rpm or more but not more than 5 000 rpm loaded and not more than 6 500 rpm when not loaded - with a power supply voltage of 100 v or more but not more than 240 v for use in the manufacture of electric fryersFree
• 8501.10.99.64 Dc motor to control angular position of the flap to adjust gas flow in the air throttle and egr valve: -with ingress protection (ip) standard of ip69, -with a rotor speed of not more than 6 500 rpm when not loaded, -with a rated voltage of 12,0 v (± 0,1), -of a specified temperature range of - 40 °c or more but not more than 165 °c, -with or without a connecting pinion, -with or without an engine connector, -with or without a flange, -with a diameter of not more than 40 mm (not including the flange), -with an overall height of not more than 90 mm (from the base to the pinion)Free
• 8501.10.99.65 Electric turbocharger actuator, with: - a dc motor, - an integrated gear mechanism, - a (pulling)force of 200 n or more at a minimum of 140°c elevated ambient temperature, - a (pulling) force of 250 n or more in each position of its stroke, - an effective stroke of 15 mm or more but not more than 25 mm, - with or without an on-board diagnostics interfaceFree
• 8501.10.99.70 Dc stepping motor, with - a two-phase winding, - a rated voltage of 9 v or more, but not more than 16,0 v - of a specified temperature range covering at least - 40 degc to + 105 degc - with or without connecting pinion - with or without motor drive connectorFree
• 8501.10.99.75 Permanently excited dc motor with - a multiple-phase winding, - an external diameter of 24 mm or more but not more than 38 mm, - a rated speed of not more than 12 000 rpm, - a power supply voltage of 8 v or more but not more than 27 v, - with or without a pulley, - with or without a gear wheelFree
• 8501.10.99.79 Dc motor with brushes and an internal rotor with a three-phase winding, whether or not equipped with a worm or a pinion, of a specified temperature range covering at least - 20°c to + 70°cFree
• 8501.10.99.90 OtherFree

8501.20 Electric motors; universal AC/DC of an output exceeding 37.5W

• 8501.20.00.10 Of an output exceeding 735 w but not exceeding 150 kw, for use in civil aircraftFree
• 8501.20.00.20 Of an output of less than 750 w or exceeding 150 kw, for use in certain types of aircraftFree
• 8501.20.00.50 Universal ac/dc motor, rotating: -with a nominal supply voltage of 230 v, -with a power of more than 37,5 w but not more than 2 000 w, -with a stator cross-section of 93 mm or more but not more than 103 mm and a thickness of 15 mm or more but not more than 45 mm, and -with or without a worm gear, gears or a gearbox, for the production of a torque to a transmission shaft for small domestic appliancesFree
• 8501.20.00.60 Universal ac/dc motor, rotating: -with a nominal supply voltage of 230 v, -with a power of more than 37,5 w but not more than 1 200 w, -with a stator cross-section of 65 mm or more but not more than 75 mm and a thickness of 15 mm or more but not more than 45 mm, and -with or without a worm gear, gears or a gearbox, for the production of a torque to a transmission shaft for small domestic appliancesFree
• 8501.20.00.70 Universal ac/dc motor, rotating: -with a nominal supply voltage of 230 v, -with a power of more than 37,5 w but not more than 700 w, -with a stator cross-section of 49 mm or more but not more than 59 mm and a thickness of 15 mm or more but not more than 45mm, and -with or without a worm gear, gears or a gearbox, for the production of a torque to a transmission shaft for small domestic appliancesFree
• 8501.20.00.90 OtherFree

8501.31 Electric motors and generators; DC, of an output not exceeding 750W

• 8501.31.00.10 Motors of an output exceeding 735 w, dc generators, for use in civil aircraftFree
• 8501.31.00.20 For use in certain types of aircraftFree
• Other
• 8501.31.00.45 Dc motors, brushless, with: - an external diameter of 90 mm or more, but not more than 110 mm, - a rated speed of not more than 3 680 rpm, - an output of 600 w or more but not more than 740 w at 2 300 rpm and at 80 °c, - a supply voltage of 12 v, - a torque of not more than 5,67 nm, - a rotor position sensor, - an electronic star-point relay, and - for use with an electric power steering control moduleFree
• 8501.31.00.47 Motor for automotive electric seat adjustment applications: -with a shaft output on both motor sides, -consisting of a permanently excited dc motor, -whether brushed or brushless, -whether or not with electronic control unit, -whether or not with hall effect sensor, -with a nominal voltage of 8 v or more but not more than 16 v, -with a rated output mechanical power not exceeding 120 w, and -with a specified temperature range from -40 °c to 160 °c, for use in the manufacture of automotive components for car's seatsFree
• 8501.31.00.48 Brushless dc electric motors: -with a rated power of 240 w or more, but not more than 260 w, -with a voltage of 36 v or higher, but not higher than 52 v -with a torque of 20 nm or more, but not more than 140 nm, -with a housing made of aluminum, aluminum alloy or plastic, -with or without a built-in controller, -with a communication function in the lin or uart interface, -weighing 1,5 kg or more, but not more than 5,0 kg, -adapted for mounting in a bicycle frame for use in the manufacture of e-bikesFree
• 8501.31.00.49 Brushless dc electric motors: - with a rated power of 240 w or more, but not more than 260 w, - with a voltage of 24 v or higher, but not higher than 52 v, - with a torque of 30 nm or more, but not more than 62 nm, - with a lin, uart or can communication interface, - with an internal planetary gearbox with fixed or variable ratio or direct drive, - with a housing made of aluminum or aluminium alloy, - with a weight of 1,5kg or more, but not more than 6kg, - adapted for mounting in the front or rear bicycle wheel, for use in the manufacture of e-bikesFree
• 8501.31.00.50 Dc motors, brushless, with: - an external diameter of 80 mm or more, but not more than 200 mm, - a supply voltage of 4 v or more, but not more than 16 v, - an output at 20 °c of 200 w or more, but not more than 750 w, - a torque at 20 °c of 2,00 nm or more, but not more than 7,00 nm, - a rated speed at 20 °c of 600 rpm or more, but not more than 3 100 rpm, - with or without a pulley, - with or without an electronic power steering sensor/controllerFree
• 8501.31.00.52 Electric brushless direct current motor finished with biocompatible materials such as stainless steel according to specification 17-4 ph or type 303, 316l, 400 with: -a three-phase winding, -an output power not exceeding 280 w, -a length with gearhead of 116,1 mm or more but not more than 117,2 mm, -an external diameter of 13,86 mm or more but no more than 13,92 mm, -a maximum torque of motor with gearhead 246,6 mnm in 25℃, -a no-load radial speed of motor with gearhead with 9 900 rpm, at 24v in 25°c, -a weight of motor with gearhead of 70,5 g or more but not more than 71,5 g, a resistance to peak temperature of 140°c or more (non-operating), a maximal air leak between shaft and shaft seals of 15 pa/s at given 2 bars of pressure, -14 functional pins for power and control purpose, -a flexible printed circuit with length of 245 mm but no longer than 255 mm with mounted 8 pin male connector for use in the manufacture of medical devices with right-left rotation and oscillation functionFree
• 8501.31.00.54 Brushless dc electric motor, with: -a rated voltage of 310 v, -a rated power of 350 w or more but not more than 368 w, -an input power of 500 w or more but not more than 550 w, -output power of 350 w or more but not more than 400 w, -an external diameter without bracket connector and pulley of 143,2 mm or more but not more than 143,8 mm, -a rated speed of 16300 rpm or more but not more than 16500 rpm, -a weight of 2,33 kg or more but not more than 2,40 kg, -a pulleyFree
• 8501.31.00.55 Dc motor with or without commutator, for driving hand-held power tools, lawn mowers or home appliances, with: -an external diameter of 24,2 mm or more, but not more than 140 mm, -a rated speed of 3300 rpm or more, but not more than 26200 rpm, -a rated supply voltage of 3,6 v or more, but not more than 230 v, -an output power of more than 37,5 w , but not more than 2400 w, -a free load current of not more than 20,1 a, -a maximum efficiency of 50 % or more,Free
• 8501.31.00.56 Dc motor, brushless, integrated with an electronic control unit (ecu), defined as a power pack with: -a safety feature and mechanism designed for prevention of critical hazards like self-steer by single failure, -a can-communication interface, -an external sensor interface, -operating temperature range of -40℃ to 95℃ or broader, -compliance with standard ip6k9k for water and dustproofness, -supply voltage of 9 v or more, but not more than 16 v, -rated power output of 500 w or more, but not higher than 750 w, -rated torque of 3 nm or more, but not more than 6 nm, -length of 150 mm or more, but not more than 250 mm, -width of 100 mm or more, but not more than 150 mm, -height of 80 mm or more, but not more than 120 mmFree
• 8501.31.00.57 Brushless dc electric motor with lcd control indicator and/or control unit with buttons: -with an output power of 200 w or more, but not more than 700 w, -with a supply voltage of 30 v or more, but not more than 60 v, -with a torque of 30 nm or more, but not more than 200 nm, -with a height of 117 mm or more, but not more than 146 mm, -with a length of 117 mm or more, but not more than 223 mm, -with a width of 135 mm or more, but not more than 190 mm, -with a weight of 2 kg or more but not more than 5 kg, -designed to be mounted in a frame, front or rear bicycle wheel, -equipped with sockets, at least for cable connection with lcd control indicator, for use in the manufacture of electric bicyclesFree
• 8501.31.00.58 Permanently excited dc motor with: -an external diameter of 27 mm or more but not more than 90 mm, including mounting flange, -a rated speed of not more than 25 000 rpm, -an output of 45 w or more but not more than 400 w, and -a supply voltage of 9 v or more but not more than 50 v, -whether or not a multiple-phase winding, -whether or not with a drive disc, -whether or not with a crankcase, -whether or not with a fan, -whether or not with a cap assembly, -whether or not with a sun gear, -whether or not with a speed and rotational direction encoder, -whether or not with or without a speed or rotational direction sensor of resolver type or hall effect type, -whether or not with a mounting flange for use in the manufacture of air suspension seats in tractors, earthmoving machines and forklifts or for use in the manufacture of actuators for height-adjustable furnitureFree
• 8501.31.00.63 Ready for installation in vehicles or equipment of headings 8432 and 8433, brushless and permanently excited direct current motor with: - a specified speed of not more than 6000rpm, - a minimum output of 400w, but not more than 1,3kw (at 12 v), or with a minimum output of 750w but not more than 1,55kw (at 36 v), - a flange diameter of 85mm or more but not more than 200mm, - a maximum length of 335mm, measured from the beginning of the shaft to the outer ending, - a housing length of not more than 265mm, measured from the flange to the outer ending, - a maximum of two-piece (basic housing including electric components and flange with minimum 2 and maximum 11 bore holes) aluminium diecast or sheet steel housing whether or not with a sealing compound (groove with an o-ring and grease), - a stator with single t-tooth design and single coil windings in 9/6 or 12/8 or 12/10 topology, and - surface magnets, - whether or not with electronic power steering controller, - whether or not with pulley or coupling, - whether or not with rotor position sensorFree
• 8501.31.00.68 Camshaft actuator for controlling the timing of valve opening by using electromotor in a continuous variable valve timing system of an internal combustion piston engine, of: -a length of 110 mm or more but not more than 140 mm, -a width of 90 mm or more but not more than 130 mm, -a height of 80 mm or more but not more than 110 mm for use in the manufacture of engines of motor vehiclesFree
• 8501.31.00.85 Power transmission device for controlling the output of exhaust gas turbochargers, consisting of: - a dc motor of an output not exceeding 600 w, - for usage with a supply voltage of 8 v or more but no more than 48 v, - with motor connection (plug-in connection), - whether or not with position sensor, - whether or not with integrated control and power electronics, - whether or not with spring mechanism for resetting the lever, - built in a housing with reduction gear and lever attached to the motor drive shaft, or - built in a housing with threads integrated into the rotor of the motor for linear movement of the integrated control rodFree
• 8501.31.00.99 OtherFree

8501.32 Electric motors and generators; DC, of an output exceeding 750W but not exceeding 75kW

• 8501.32.00.10 For use in civil aircraftFree
• Other
• 8501.32.00.40 Dc motor with or without commutator, for driving hand-held power tools, lawn mowers or home appliances, with: -an external diameter of 24,2 mm or more, but not more than 140 mm, -a rated speed of 3300 rpm or more, but not more than 26200 rpm, -a rated supply voltage of 3,6 v or more, but not more than 230 v, -an output power of more than 37,5 w , but not more than 2400 w, -a free load current of not more than 20,1 a, -a maximum efficiency of 50 % or more,Free
• 8501.32.00.65 Ready for installation in vehicles or equipment of headings 8432 and 8433, brushless and permanently excited direct current motor with: - a specified speed of not more than 6000rpm, - a minimum output of 400w, but not more than 1,3kw (at 12 v), or with a minimum output of 750w but not more than 1,55kw (at 36 v), - a flange diameter of 85mm or more but not more than 200mm, - a maximum length of 335mm, measured from the beginning of the shaft to the outer ending, - a housing length of not more than 265mm, measured from the flange to the outer ending, - a maximum of two-piece (basic housing including electric components and flange with minimum 2 and maximum 11 bore holes) aluminium diecast or sheet steel housing whether or not with a sealing compound (groove with an o-ring and grease), - a stator with single t-tooth design and single coil windings in 9/6 or 12/8 or 12/10 topology, and - surface magnets, - whether or not with electronic power steering controller, - whether or not with pulley or coupling, - whether or not with rotor position sensorFree
• 8501.32.00.99 OtherFree

8501.33 Electric motors and generators; DC, of an output exceeding 75kW but not exceeding 375kW

• 8501.33.10.00 Hydrogen fuel cell generatorsFree
• Other
• 8501.33.90.10 Motors of an output not exceeding 150 kw and generators, for use in civil aircraftFree
• 8501.33.90.20 Of an output exceding 150 kw, for use in certain types of aircraftFree
• 8501.33.90.30 Electric drive for motor vehicles, with an output of not more than 315 kw: -with an ac or dc motor with or without transmission, -with or without power electronicsFree
• 8501.33.90.99 OtherFree

8501.34 Electric motors and generators; DC, of an output exceeding 375kW

• 8501.34.00.10 Generators for use in civil aircraftFree
• 8501.34.00.99 OtherFree

8501.40 Electric motors; AC motors, single-phase

• Of an output not exceeding 750 w
• 8501.40.20.10 Of an output exceeding 735 w, for use in civil aircraftFree
• 8501.40.20.20 For use in certain types of aircraftFree
• 8501.40.20.35 Electric ac motor, single-phase, with: -a rated power of 120 w or more but not more than 150 w, -an input power of 280 w or more but not more than 350 w, -an external diameter without bracket connector and pulley of 145 mm or more but not more than 160 mm, -a rated speed of 2 680 rpm or more but not more than 3 000 rpm, -a weight of 4,2 kg or more but not more than 4,6 kg, -pulleys, a spindle and a tachometer, for use in the manufacture of home appliance productsFree
• 8501.40.20.45 Electric ac motor, single-phase, with: -a rated power of 275 w or more, but not more than 325 w, -an input power of 600 w or more but not more than 700 w, -an external diameter without bracket and connector of 150 mm or more but not more than 170 mm, -a rated speed of 15 000 rpm or more but not more than 20 000 rpm, -a weight of 4,2 kg or more, -a pulley and a tachometer, for use in the manufacture of home appliance productsFree
• 8501.40.20.50 Electric ac motor, single-phase, with: -a rated power of 300 w or more but not more than 370 w, -an input power of 600 w or more but not more than 700 w, -an external diameter without bracket and connector of 150 mm or more but not more than 170 mm, -a rated speed of 15 000 rpm or more but not more than 19 000 rpm, -a weight of 4,8 kg or more, -a pulley, for use in the manufacture of home appliance productsFree
• 8501.40.20.55 Electric ac motor, single-phase, with: -a rated power of 275 w or more, but not more than 325 w, -an input power of 600 w or more but not more than 700 w, -an external diameter without bracket and connector of 160 mm or more but not more than 180 mm, -a rated speed of 15 000 rpm or more but not more than 19 000 rpm, -a weight of not more than 4,4 kg, -a pulley, for use in the manufacture of home appliance productsFree
• 8501.40.20.60 Electric ac motor, single-phase, with: -a rated power of 275 w or more but not more than 325 w, -an output power of 550 w or more but not more than 600 w, -an input power of 800 w or more but not more than 1 000 w, -an external diameter of more than 150 mm but not more than 170 mm without the bracket, -a rated speed of more than 16 000 rpm but not more than 18 000 rpm, -a weight of 3,4 kg or more but not more than 3,7 kg, -a pulley, for use in the manufacture of home appliance productsFree
• 8501.40.20.70 Electric ac motor, single-phase, whether or not with commutator - with a nominal output of 180 w or more, - with an input power of 150 w or more but not more than 2 700 w, - with an external diameter of more than 44,8 but not more than 135,2 mm, - with a rated speed of more than 10 000 rpm but not more than 50 000 rpm, - whether or not equipped with air-inducting ventilator, - whether or not with mechanical device (pinion, screws, gear connection etc.) on the shaft, for use in the manufacture of domestic appliancesFree
• 8501.40.20.75 Incomplete, single-phase brushless ac motor consisting of a rotor and a stator: -a rotor on the inside is equipped with a ring of 12 magnets housed in a steel casing, -a stator with an internal diameter of 206,6 mm (± 0,5 mm), external diameter of 265,0 mm (± 0,2 mm) and width of 37,2 mm or more but not more than 47,8 mm, -with a rated power not exceeding 750 w, -with a weight of 5 kg or more, for use in the production of washing machines, washer-dryers equipped with a drum with direct driveFree
• 8501.40.20.80 OtherFree
• Of an output exceeding 750 w
• 8501.40.80.10 Of an output not exceeding 150 kw, for use in civil aircraftFree
• 8501.40.80.20 Of an output exceeding 150 kw, for use in certain types of aircraftFree
• 8501.40.80.50 Electric drive for motor vehicles, with an output of not more than 315 kw: -with an ac or dc motor with or without transmission, -with or without power electronicsFree
• 8501.40.80.70 Electric ac motor, single-phase, whether or not with commutator - with a nominal output of 180 w or more, - with an input power of 150 w or more but not more than 2 700 w, - with an external diameter of more than 44,8 but not more than 135,2 mm, - with a rated speed of more than 10 000 rpm but not more than 50 000 rpm, - whether or not equipped with air-inducting ventilator, - whether or not with mechanical device (pinion, screws, gear connection etc.) on the shaft, for use in the manufacture of domestic appliancesFree
• 8501.40.80.90 OtherFree

8501.51 Electric motors; AC motors, multi-phase, of an output not exceeding 750W

• 8501.51.00.10 Of an output exceeding 735 w, for use in civil aircraftFree
• 8501.51.00.20 Of an output of less than 750 w, for use in certain types of aircraftFree
• 8501.51.00.25 Electric permanent magnet synchronous motor with: -an output power of 550 w, -a rotor containing 8 poles generated by permanent magnets composed mainly with neodymium-iron-boron (per gb/t 13560 standard) enclosed in polyethylene cover, -an outer diameter of motor magnet shaft end with dimension of 10,001 mm or more but no more than 10,007 mm, -terminals located across the radius 32,5 mm and separated by an angle of 21,8°, -a motor housing made of adc12 or ac46000 aluminium alloy die casting with composition of aluminium-silicon-copper (per jis h5302 or en1706 standard), -a back electromotive force constant (ke) of 0,03306 v-sec/rad or more but no more than 0,03654 v-sec/rad, -a back electromotive force harmonic order - 5th of no more than 0,38 % (of fundamental) and 7th of no more than 0,25 % (of fundamental), -a cogging torque of no more than 13 mnm, -a friction torque in ambient temperature of no more than 22 mnm, -a maximum temperature of motor operation of no more than 200 °cFree
• 8501.51.00.30 Ac synchronous servo motor with resolver and brake for a maximum speed of not more than 6 000rpm,with: - an output of 340w or more but not more than 7,4kw, - a flange of dimensions of not more than 180mm × 180mm, and - a length from flange to extreme end of resolver of not more than 271mmFree
• 8501.51.00.35 Electric permanent magnet synchronous motor with: -an output power of 600 w, -a rotor containing 8 poles generated by permanent magnets composed mainly with neodymium-iron-boron and dysprosium enclosed in aluminium cover, -an outer diameter of motor magnet shaft end with dimension of 10,001 mm or more but no more than 10,007 mm, -terminals located across the diameter 59,2 mm and separated by an angle 30,0°, -a housing made of electrogalvanized steel (per jis g3313 grade sece standard) using a deep-drawing stamping process, -a diameter of 88,600 mm or less but no less than 88,546 mm at the motor-system assembly interface, -a back electromotive force constant (ke) of 0,03277 v-sec/rad or more but no more than 0,03623 v-sec/rad, -a back electromotive force harmonic order - 5th of no more than 0,35 % (of fundamental) and 7th of no more than 0,30 % (of fundamental), -a cogging torque of no more than 12 mnm, -a friction torque in ambient temperature of no more than 23 mnm, -a maximum temperature of motor operation of no more than 200 °cFree
• 8501.51.00.40 Electric ac motor, three-phase, with: -a rated power of 280 w or more but not more than 320 w, -an output power of 480 w or more but not more than 540 w, -an input power of 800 w or more but not more than 900 w, -an external diameter of 150 mm or more but not more than 170 mm, -a rated speed of 15 000 rpm or more but not more than 20 000 rpm, -a weight of 6 kg or more but not more than 6,4 kg, -a pulley and a tachometer, for use in the manufacture of home appliance productsFree
• 8501.51.00.45 Automotive-ready brushless permanently excited magnet synchronous alternating current motor with: -a specified speed of not more than 7000 rpm, -an output of 400 w or more but not more than 750 w (at 12 v), -a flange diameter of 80 mm or more, but not more than 200 mm, -a maximum length of not more than 335 mm, measured from the beginning of the shaft to its outer end, -a housing length of not more than 265 mm, measured from the flange to the outer end, -a steel sheet or die-cast aluminium basic housing consisting of not more than two parts, including electrical components and a flange with two or more but not more than 11 holes, whether or not with a sealing connection (groove with o-ring and protective grease or liquid seal interface), -a stator with single t-tooth design and single coil winding with 9/6 or 12/10 or 12/8 topology and surface magnets, -whether or not with electronic power steering controller, -whether or not with pulley or coupling, -whether or not with rotor position sensorFree
• 8501.51.00.50 Three phase ac synchronous brushless permanent magnet motor with: -an output of 500 w or more but not more than 700 w, -an external diameter of 129,7 mm or more but not more than 180,3 mm, -a rated speed of 16 000 rpm or more but not more than 17 000 rpm, -a weight of 2,5 kg or more but not more than 3,1 kg, and -with a pulley, for use in the manufacture of home appliance productsFree
• 8501.51.00.90 OtherFree

8501.52 Electric motors; AC motors, multi-phase, of an output exceeding 750W but not exceeding 75kW

• Of an output exceeding 750 w but not exceeding 7,5 kw
• 8501.52.20.10 For use in civil aircraftFree
• Other
• 8501.52.20.50 Ac synchronous servo motor with resolver and brake for a maximum speed of not more than 6 000rpm,with: - an output of 340w or more but not more than 7,4kw, - a flange of dimensions of not more than 180mm × 180mm, and - a length from flange to extreme end of resolver of not more than 271mmFree
• 8501.52.20.55 Brushless synchronous alternating current electric motors with permanent magnets, with: -an output power of 1000 w or more, but not more than 1400 w, -a rotor containing 8 poles, generated by permanent magnets composed mainly of praseodymium-neodymium-iron-boron (gb/t 13560-2017 standard), enclosed in a stainless steel cover, -a motor magnet shaft end outer diameter of 10,001 mm or more, but not more than 10,007 mm, -motor terminals located across the 37,00 mm radius and separated by an angle of 30,00 °, -a motor housing made of adc12 or en ac46000 aluminium alloy die casting with composition of aluminium-silicon-copper (per jis h5302-2000 or en 1706 standard), -a back electromotive force constant (ke) of 0,0265 v-sec/rad or more, but not more than 0,0293 v- sec/rad, -a back electromotive force (emf) harmonic order - 5th of no more than 0,4 % (of fundamental) and 7th of no more than 0,2 % (of fundamental), -a synchronous inductance of 33,49 µh or more, but not more than 37,01 µh, -a cogging torque of not more than 15 mnm, -a friction torque in ambient temperature of not more than 20 mnm, -a maximum motor operation temperature of not more than 200 °c, -with or without a spline on the motor shaftFree
• 8501.52.20.70 Automotive-ready brushless permanently excited magnet synchronous alternating current motor with: -a specified speed of not more than 7000 rpm, -an output of 750 w or more but not more than 1,8 kw (at 12 v), -a flange diameter of 80 mm or more, but not more than 200 mm, -a maximum length of not more than 335 mm, measured from the beginning of the shaft to its outer end, -a housing length of not more than 265 mm, measured from the flange to the outer end, -a steel sheet or die-cast aluminium basic housing consisting of not more than two parts, including electrical components and a flange with two or more but not more than 11 holes, whether or not with a sealing connection (groove with o-ring and protective grease or liquid seal interface), -a stator with single t-tooth design and single coil winding with 9/6 or 12/10 or 12/8 topology and surface magnets, -whether or not with electronic power steering controller, -whether or not with pulley or coupling, -whether or not with rotor position sensorFree
• 8501.52.20.80 Electric permanent magnet synchronous motor with: -an output power of 850 w, -a rotor containing 8 poles generated by permanent magnets composed mainly with neodymium-iron-boron (per gb/t 13560 standard) enclosed in polyethylene cover, -an outer diameter of motor magnet shaft end with dimension of 10,001 mm or more but no more than 10,007 mm, -terminals located across the radius 26,2 mm and separated by an angle 30,0°, -a housing made of adc12 or ac46000 aluminium alloy die casting with composition of aluminium-silicon-copper (per jis h5302 or en1706 standard) and anodized coating (per astm b580 type e standard), -a back electromotive force constant (ke) of 0,04009 v-sec/rad or more but no more than 0,04431 v-sec/rad, -a back electromotive force harmonic order - 5th of no more than 0,36 % (of fundamental) and 7th of no more than 0,24 % (of fundamental), -a cogging torque of no more than 20 mnm, -a friction torque in ambient temperature of no more than 26,5 mnm, -a maximum temperature of motor operation of no more than 200 °cFree
• 8501.52.20.89 OtherFree
• Of an output exceeding 7,5 kw but not exceeding 37 kw
• 8501.52.30.10 For use in civil aircraftFree
• 8501.52.30.90 OtherFree
• Of an output exceeding 37 kw but not exceeding 75 kw
• 8501.52.90.10 For use in civil aircraftFree
• 8501.52.90.90 OtherFree

8501.53 Electric motors; AC motors, multi-phase, of an output exceeding 75kW

• Traction motors
• 8501.53.50.10 Electric drive for motor vehicles, with an output of not more than 315 kw: -with an ac or dc motor with or without transmission, -with or without power electronicsFree
• 8501.53.50.20 Ac traction motor of the interior permanent magnet synchronous motor (ipmsm) type with: -a torque output of 200 nm or more, but not more than 400 nm, -a power output of 50 kw or more, but not more than 200 kw , -a rotation speed of no more than 15 000 rpm, for use in the manufacture of electric vehiclesFree
• 8501.53.50.30 Permanent magnet synchronous traction motor, with: -a continuous power of 110 kw or more but not more than 180 kw, -a liquid cooled system, -a total length of 500 mm or more but not more than 650 mm, -a total width of 600 mm or more but not more than 700 mm, -a total height of 550 mm or more but not more than 650 mm, -weighing of not more than 350 kg, -3 suspension pointsFree
• 8501.53.50.40 Permanent magnet traction ac motor, with: -a continuous power of 110 kw or more but not more than 150 kw, -a liquid cooled system, -a total length of 460 mm or more but not more than 590 mm, -a total width of 450 mm or more but not more than 580 mm, -a total height of 490 mm or more but not more than 590 mm, -a weight of not more than 310 kg, -4 mounting pointsFree
• 8501.53.50.50 Asynchronous traction motor, with: -a continuous power of 140 kw or more but not more than 180 kw, -a liquid cooled system, -a total length of 580 mm or more but not more than 730 mm, -a total width of 550 mm or more but not more than 670 mm, -a total height of 510 mm or more but not more than 630 mm, -with a weight of not more than 390 kg, -with or without reduction gear, -with or without starter generator, -2 mounting points, for use in the manufacture of the electric drive of hybrid busesFree
• 8501.53.50.90 OtherFree
• Other, of an output
• Exceeding 75 kw but not exceeding 375 kw
• 8501.53.81.10 Of an output not exceeding 150 kw, for use in civil aircraftFree
• 8501.53.81.20 Of an output exceeding 150 kw, for use in certain types of aircraftFree
• 8501.53.81.90 OtherFree
• Exceeding 375 kw but not exceeding 750 kw
• 8501.53.94.10 For use in certain types of aircraftFree
• 8501.53.94.90 OtherFree
• Exceeding 750 kw
• 8501.53.99.10 For use in certain types of aircraftsFree
• 8501.53.99.90 OtherFree

8501.61 Generators; AC generators, (alternators), other than photovoltaic generators, of an output not exceeding 75kVA

• Of an output not exceeding 7,5 kva
• 8501.61.20.10 For use in civil aircraftFree
• 8501.61.20.90 OtherFree
• Of an output exceeding 7,5 kva but not exceeding 75 kva
• 8501.61.80.10 For use in civil aircraftFree
• 8501.61.80.99 OtherFree

8501.62 Electric generators; AC generators, (alternators), other than photovoltaic generators, of an output exceeding 75kVA but not exceeding 375kVA

• 8501.62.00.10 For use in civil aircraftFree
• 8501.62.00.40 Ac, 3-phase generator, with: -a continuous power of 147 kva or more but not more than 222 kva, -a continuous torque of 650 nm or more but not more than 900 nm, -a maximum working speed of 2700 revolutions per minute (rpm), -a liquid cooled system, -a length of 100 mm or more but not more than 200 mm, -a width of 550 mm or more but not more than 650 mm, -a height of 550 mm or more but not more than 650 mm, -weighing of not more than 150 kgFree
• 8501.62.00.98 OtherFree

8501.63 Electric generators; AC generators, (alternators), other than photovoltaic generators, of an output exceeding 375kVA but not exceeding 750kVA

• 8501.63.00.10 For use in civil aircraftFree
• 8501.63.00.99 OtherFree

8501.64 Electric generators; AC generators, (alternators), other than photovoltaic generators, of an output exceeding 750kVA

• 8501.64.00.00 Of an output exceeding 750 kvaFree

8501.71 Electric generators; photovoltaic DC generators, of an output not exceeding 50W

• 8501.71.00.00 Of an output not exceeding 50 wFree

8501.72 Electric generators; photovoltaic DC generators, of an output exceeding 50W

• 8501.72.00.00 Of an output exceeding 50 wFree

8501.80 Electric generators; (excluding generating sets), photovoltaic AC generators (alternators)

• 8501.80.00.00 Photovoltaic ac generatorsFree