8414 Air or vacuum pumps, air or other gas compressors and fans; ventilating or recycling hoods incorporating a fan; gas-tight biological safety cabinets whether or not fitted with filters

8414.10 Pumps; vacuum

• 8414.10.15.00 Of a kind used for the manufacture of semiconductors or solely or principally used for the manufacture of flat panel displaysFree
• Other
• Rotary piston pumps, sliding vane rotary pumps, molecular drag pumps and roots pumps
• 8414.10.25.10 For use in civil aircraftFree
• 8414.10.25.30 Tandem pump consisting of: -an oil pump with displacement of 21,6 cc/rev (± 2 cc/rev) and working pressure 1,5 bar at 1 000 revolutions per minute, -vacuum pump with displacement of 120 cc/rev (± 12 cc/rev) and performance of -666 mbar in 6 seconds at 750 revolutions per minute for use in the manufacture of engines of motor vehiclesFree
• 8414.10.25.90 OtherFree
• Other
• Diffusion pumps, cryopumps and absorption pumps
• 8414.10.81.10 For use in civil aircraftFree
• 8414.10.81.90 OtherFree
• Other
• 8414.10.89.10 For use in civil aircraftFree
• 8414.10.89.90 OtherFree

8414.20 Pumps; hand or foot-operated air pumps

• 8414.20.20.00 Handpumps for cyclesFree
• Other
• 8414.20.80.10 For use in civil aircraft—
• 8414.20.80.90 Other2%

8414.30 Compressors; of a kind used in refrigerating equipment

• Of a power not exceeding 0,4 kw
• 8414.30.20.10 For use in civil aircraft—
• 8414.30.20.60 Hermetic compressor for r290 refrigerant for the production of refrigerators and freezers: -with a power not exceeding 0.4 kw, -pre-filled with lubricant from 190 ml to 210 ml, -suction and processing pipe inner diameter from 6.40 mm to 6.60 mm, -discharge pipe inner diameter from 4.80 mm to 5.00 mm, -driven by a brushless dc motor, -cooling capacity from 340 to 360 w at ashrae lbp 3000 rpm, -displacement from 6.5 cm³ to 7.5 cm³, -speed range from 1,600 rpm to 4,200 rpm2%
• 8414.30.20.90 Other2%
• Of a power exceeding 0,4 kw
• Hermetic or semi-hermetic
• 8414.30.81.10 For use in civil aircraft—
• Other
• 8414.30.81.50 Hermetic or semi-hermetic variable-speed electric scroll compressors, with a nominal power rating of 0,5 kw or more but not more than 10 kw, with a displacement volume of not more than 35 cm³, of the type used in refrigeration equipment2%
• 8414.30.81.60 Hermetic rotary compressors for either hydrofluorocarbon (hfc) or hydrocarbon refrigerants: - driven by ‘on-off’ single phase alternate current (ac) or ‘brushless direct current’ (bldc) variable speed motors, - with a nominal power rating of not more than 1,5kw, - a rated voltage of 100v or more but not more than 240v, - with a height of not more than 300mm, - an external diameter of not more than 150mm, - with a unit weight of not more than 15kg, for use in the manufacture of heat pumps for household appliances, including clothes dryers2%
• 8414.30.81.89 Other2%
• Other
• 8414.30.89.10 For use in civil aircraft—
• 8414.30.89.20 Vehicle air conditioning system part, consisting of an open shaft reciprocating compressor of a power of more than 0,4 kw but not more than 10 kw2%
• 8414.30.89.40 Electrical compressor for motor vehicle air conditioning system: -with a power output of more than 0,4 kw but not exceeding 10 kw, for use in the manufacture of motor vehicles of subheading 8703 402%
• 8414.30.89.90 Other2%

8414.40 Compressors; air compressors mounted on a wheeled chassis for towing

• 8414.40.10.00 Giving a flow per minute not exceeding 2 m32%
• 8414.40.90.00 Giving a flow per minute exceeding 2 m32%

8414.51 Fans; table, floor, wall, window, ceiling or roof fans, with a self-contained electric motor of an output not exceeding 125W

• 8414.51.00.10 For use in civil aircraft—
• 8414.51.00.90 Other2%

8414.59 Fans; n.e.c. in item no. 8414.51

• 8414.59.15.00 Fans of a kind used solely or principally for cooling microprocessors, telecommunication apparatus, automatic data processing machines or units of automatic data processing machinesFree
• Other
• Axial fans
• 8414.59.25.10 For use in civil aircraft—
• 8414.59.25.50 Axial fans with built-in motor, for the generation of an air flow for the cooling of compressors and the distribution of air with -a direct current operating voltage of more than 10 v but not more than 14 v, or -an alternating current operating voltage of more than 185 v, but not more than 254 v, -an operating temperature of -40 °c or higher, but not higher than 70 °c, for use in the manufacture of heat pump tumble dryers and refrigerators or freezers2%
• 8414.59.25.60 Axial fan, for incorporation into instrument clusters, speedometers and infotainment systems of transport vehicles as motor vehicles of headings 8701 to 8705, with: -an air flow of not more than 0,75 m3/min (cubic meter per minute) -an air pressure of not more than 10 mmh2o -an overall acoustic noise of not more than 45 db(a) -a diameter of not more than 65mm equipped with dc brushless motor with: -a rated voltage between: 3 to 16 vdc -an operating voltage between: 3 to 16 vdc -a rated current between: 0,03 to 0,30 a -an input power between: 0,3 to 1,5 w -a rotation speed between: 2500 to 10000 r.p.m, with or without a heat sink incorporated2%
• 8414.59.25.90 Other2%
• Centrifugal fans
• 8414.59.35.10 For use in civil aircraft—
• 8414.59.35.20 Radial fan, with: -a dimension of 25mm (height) x 85mm (width) x 85mm (depth), -a weight of 120 g, -a rated voltage of 13,6 vdc (direct current voltage), -an operating voltage of 9 vdc or more but not more than 16 vdc (direct current voltage), -a rated current of 1,1 a (typ), -a rated power of 15 w, -a rotation speed of 500 rpm (revolutions per minute) or more but not more than 4800 rpm (revolutions per minute) (free flow), -an air flow of not more than 17,5 litre/s, -an air pressure of not more than16 mm h2o ≈ 157 pa, -an overall sound pressure of not more than 58 db(a) at 4800 rpm (revolutions per minute), and with a fin (fan interconnect network) interface for communication with the heating and air-conditioning control unit used in car seat ventilation systems2%
• 8414.59.35.30 Electric blower for cooling the high-voltage battery of a hybrid passenger car with: -a control unit, -mosfet inverter, -a voltage of 9 v or more but not more than 16 v, -ambient temperature of - 40 °c or more, but not more than 80 °c, for use in the manufacture of hybrid passenger cars2%
• 8414.59.35.40 Electric blower for cooling the battery module: -with an operating voltage of 9 vdc or more but not more than 16 vdc, -with a centrifugal electric fan, -with a connector, -with a plastic case, -with or without a control unit for the fan electric motor, for use in the production of rechargeable batteries for hybrid and electric vehicles2%
• 8414.59.35.50 Dc motor centrifugal fan with: -a nominal voltage of 8 v or more, but not more than 13 v, -a nominal maximum speed of 1400 rpm or more, but not more than 1950 rpm, -a horizontal or vertical position of the fan blades shaft, -a boosting time of not more than 10 seconds, -a cable with a length of 30 cm or more, but not more than 50 cm, with rast 2,5 connector, -a nominal power of 0,7 w or more, but not more than 3,5 w, -a tacho or feedback signal to monitor the speed2%
• 8414.59.35.90 Other2%
• Other
• 8414.59.95.10 For use in civil aircraft—
• 8414.59.95.90 Other2%

8414.60 Hoods; ventilating or recycling hoods incorporating a fan, whether or not fitted with filters, having a maximum horizontal side not exceeding 120cm

• 8414.60.00.00 Hoods having a maximum horizontal side not exceeding 120 cm2%

8414.70 Gas-tight biological safety cabinets; whether or not fitted with filters, having a maximum horizontal side not exceeding 120cm

• 8414.70.00.00 Gas-tight biological safety cabinetsFree

8414.80 Pumps and compressors; for air, vacuum or gas, n.e.c. in heading no. 8414

• Turbo-compressors
• Single-stage
• 8414.80.11.10 For use in civil aircraft—
• 8414.80.11.90 Other2%
• Multi-stage
• 8414.80.19.10 For use in civil aircraft—
• 8414.80.19.90 Other2%
• Reciprocating displacement compressors, having a gauge pressure capacity of
• Not exceeding 15 bar, giving a flow per hour
• Not exceeding 60 m3
• 8414.80.22.10 For use in civil aircraft—
• 8414.80.22.20 Air membrane compressor with: - a flow of 4,5 l/min or more, but not more than 12 l/min, - power input of not more than 14 w, and - a gauge pressure capacity not exceeding 400 hpa (0,4 bar) of a kind used in the production of motor vehicle seats2%
• 8414.80.22.90 Other2%
• Exceeding 60 m3
• 8414.80.28.10 For use in civil aircraft—
• 8414.80.28.90 Other2%
• Exceeding 15 bar, giving a flow per hour
• Not exceeding 120 m3
• 8414.80.51.10 For use in civil aircraft—
• 8414.80.51.90 Other2%
• Exceeding 120 m3
• 8414.80.59.10 For use in civil aircraft—
• 8414.80.59.90 Other2%
• Rotary displacement compressors
• Single-shaft
• 8414.80.73.10 For use in civil aircraft—
• Other
• 8414.80.73.30 Hermetic rotary compressors for either hydrofluorocarbon (hfc) or hydrocarbon refrigerants: - driven by ‘on-off’ single phase alternate current (ac) or ‘brushless direct current’ (bldc) variable speed motors, - with a nominal power rating of not more than 1,5kw, - a rated voltage of 100v or more but not more than 240v, - with a height of not more than 300mm, - an external diameter of not more than 150mm, - with a unit weight of not more than 15kg, for use in the manufacture of heat pumps for household appliances, including clothes dryers2%
• 8414.80.73.50 Hermetic heat pump compressor for r450a or r290 refrigerants: - not charged with refrigerant, - pre-charged with lubricant oil, - with a single phase induction permanent split capacitor motor or a dc brushless motor, - having suction and/or discharge connections, - with a displacement of 8,05 cm3 or more, but not more than 55 cm3, - running at 900 rpm or more, but not more than 7 800 rpm, and - with a cooling capacity of 920 w or more, but not more than 10 440 w in ashrae conditions2%
• 8414.80.73.89 Other2%
• Multi-shaft
• Screw compressors
• 8414.80.75.10 For use in civil aircraft—
• 8414.80.75.90 Other2%
• Other
• 8414.80.78.10 For use in civil aircraft—
• 8414.80.78.90 Other2%
• Other
• 8414.80.80.10 For use in civil aircraft—
• 8414.80.80.90 Other2%

8414.90 Pumps and compressors; parts, of air or vacuum pumps, air or other gas compressors and fans, ventilating or recycling hoods incorporating a fan

• 8414.90.00.10 For use in civil aircraft—
• 8414.90.00.15 Fan assembly made of aluminium and magnesium alloy: -with an outer diameter of 54 mm or more but not more than 130 mm, -with a height of 8 mm or more but not more than 30 mm, -with two discs connected by blades of involute shape, -with or without dowel, and with or without washer, for use in the manufacture of electromotors2%
• 8414.90.00.20 Aluminium pistons, for incorporation into compressors of air conditioning machines of motor vehicles2%
• 8414.90.00.25 Scroll type compressor housing of an aluminium alloy of a kind with: -a heat resistance of 200 °c or more but not more than 250 °c, -one or more fixing points suitable for mounting an actuator, for use in the manufacture of turbochargers2%
• 8414.90.00.35 Compressor head unit made of impregnated aluminium alloy for installation in air-conditioning compressors for motor vehicles with: -a width of 115 mm or more but not more than 160 mm, -a length of 115 mm or more but not more than 170 mm, -a height of 30 mm or more but not more than 100 mm, -a piece of pressure branch with pipe connection, -one or two mounting holes and -more than one overflowing hole2%
• 8414.90.00.45 Pressure casted rotor front plate or cover of an electric supercharger: -of en ac-46000 aluminium, -shot-blasted and machined, -with a hardness of 60 or more on the hardness brinell wolfram (hbw) scale (2,5/62,5, according to iso 6506), -with a tensile strength of 240 n/mm2 or more, -with a height of 22 mm or more but not more than 26 mm, -with a diameter of 128 mm or more but not more than 136 mm, -with a weight of 220 g or more but not more than 250 g2%
• 8414.90.00.55 Air conditioning compressor housing component made of aluminum alloy for installation in electric air conditioning compressors for motor vehicles: -with a width of 100 mm or more but not more than 220 mm, -with a length of 100 mm or more but not more than 230 mm, -with a height of 80 mm or more but not more than 180 mm, -with one single central bore, -machined by cnc milling or unwrought, -whether or not impregnated, -with one suction port or without2%
• 8414.90.00.80 Turbocharger wheel housing of cast aluminium alloy or cast iron: - with a heat resistance up to 400°c, - with a hole of 30 mm or more but not more than 300 mm for the insertion of the compressor wheel, for use in the automotive industry2%
• 8414.90.00.90 Other2%