8481 Taps, cocks, valves and similar appliances for pipes, boiler shells, tanks, vats or the like, including pressure-reducing valves and thermostatically controlled valves

8481.10 Valves; pressure reducing, for pipes, boiler shells, tanks, vats or the like

• Combined with filters or lubricators
• 8481.10.05.10 For use in certain types of aircraft2%
• 8481.10.05.90 Other2%
• Other
• Of cast iron or of steel
• 8481.10.19.10 For use in certain types of aircraft2%
• 8481.10.19.90 Other2%
• Other
• 8481.10.99.10 For use in certain types of aircraft2%
• 8481.10.99.40 Pressure reducing valves in a brass case with: -a length of not more than 30 mm (± 1 mm), -a width of not more than 18 mm (± 1 mm), of a kind used for incorporation in fuel delivery modules of motor vehicles2%
• 8481.10.99.90 Other2%

8481.20 Valves; for oleohydraulic or pneumatic transmissions

• Valves for the control of oleohydraulic power transmission
• 8481.20.10.20 For use in certain types of aircraft2%
• 8481.20.10.90 Other2%
• Valves for the control of pneumatic power transmission
• 8481.20.90.20 For use in certain types of aircraft2%
• 8481.20.90.90 Other2%

8481.30 Valves; check (nonreturn) valves, for pipes, boiler shells, tanks, vats or the like

• Of cast iron or of steel
• 8481.30.91.20 For use in certain types of aircraft2%
• Other
• 8481.30.91.30 Mechanical check (non-return) valve for opening and closing of the flow of fuel: -with an operating pressure of not more than 250 mpa, -with a flow rate of 45 cm³/minute or more, but not more than 55 cm³/minute, -with 4 input holes, each of them with a diameter of 1,2 mm or more, but not more than 1,6 mm, -made of steel2%
• 8481.30.91.91 Steel check (non-return) valves with: - an opening pressure of not more than 800 kpa - an external diameter not more than 37 mm2%
• 8481.30.91.99 Other2%
• Other
• 8481.30.99.20 For use in certain types of aircraft2%
• 8481.30.99.50 Mechanical check (non-return) valve for opening and closing of the flow of fuel: -with an operating pressure of not more than 250 mpa, -with a flow rate of 45 cm³/minute or more, but not more than 55 cm³/minute, -with 4 input holes, each of them with a diameter of 1,2 mm or more, but not more than 1,6 mm, -made of steel2%
• 8481.30.99.90 Other2%

8481.40 Valves; safety or relief valves, for pipes, boiler shells, tanks, vats or the like

• Of cast iron or of steel
• 8481.40.10.50 For use in certain types of aircraft2%
• 8481.40.10.90 Other2%
• Other
• 8481.40.90.10 For use in certain types of aircraft2%
• 8481.40.90.90 Other2%

8481.80 Taps, cocks, valves and similar appliances; for pipes, boiler shells, tanks, vats or the like, including thermostatically controlled valves

• Taps, cocks and valves for sinks, washbasins, bidets, water cisterns, baths and similar fixtures
• Mixing valves
• 8481.80.11.10 For use in certain types of aircraft2%
• 8481.80.11.90 Other2%
• Other
• 8481.80.19.10 For use in certain types of aircraft2%
• 8481.80.19.90 Other2%
• Central heating radiator valves
• 8481.80.31.00 Thermostatic valves2%
• 8481.80.39.00 Other2%
• Valves for pneumatic tyres and inner tubes
• 8481.80.40.10 For use in certain types of aircraft2%
• 8481.80.40.90 Other2%
• Other
• Process control valves
• 8481.80.51.00 Temperature regulators2%
• Other
• 8481.80.59.20 Pressure regulating valve for incorporation into compressors of motor vehicle air condition units2%
• 8481.80.59.30 Two-way flow control valve with housing, with: - at least 5, but not more than 16 outlet holes with at least 0,05 mm, but not more than 0,5 mm diameter, - at least 330 cm³/minute, but not more than 5 000 cm³/minute flow rate, - at least 19, but not more than 300 mpa operating pressure2%
• 8481.80.59.40 Flow-control valve - made of steel, - with an outlet hole with a diameter of at least 0,05mm or more, but not more than 0,5 mm, - with an inlet hole with a diameter of at least 0,1 mm, but not more than 1,3 mm, - with chromium nitride coating, - with a surface roughness of rp 0,42%
• 8481.80.59.50 Electromagnetic valve for quantity control with - a plunger, - a solenoid with a of coil resistance of at least 1,85 ohm, but not more than 8,2 ohm2%
• 8481.80.59.60 Electromagnetic valve for quantity control - with a solenoid with a coil resistance of at least 0,19 ohm, but not more than 0,66 ohm, and with an inductance of not more than 1 mh2%
• 8481.80.59.70 Flow-control valve -made of steel, -with an outlet hole with a diameter of at least 0,05 mm, but not more than 0,5 mm, -with an inlet hole with a diameter of at least 0,1 mm, but not more than 1,3 mm2%
• 8481.80.59.80 Solenoid valve for combustion engine oil pump to regulate the quantity of oil in the pump: -with a cable of length of 550 mm or more but not more than 700 mm incorporating an electrical connector, -with an operating pressure of not more than 5.5 bar, -with an operating voltage of 9 vdc or more but not more than 16 vdc, -with a valve's base width of 22 mm or more but not more than 27 mm, -with a valve's length of 55 mm or more but not more than 110 mm, for use in the manufacture of motor vehicle engines2%
• 8481.80.59.90 Other2%
• Other
• Gate valves
• 8481.80.61.00 Of cast iron2%
• Of steel
• 8481.80.63.50 For use in certain types of aircraft2%
• 8481.80.63.90 Other2%
• Other
• 8481.80.69.50 For use in certain types of aircraft2%
• Other
• 8481.80.69.60 Four-way reversing valve for refrigerants, consisting of: - a solenoid pilot valve - a brass valve body including valve slider and copper connections with a working pressure up to 4,5 mpa2%
• 8481.80.69.99 Other2%
• Globe valves
• 8481.80.71.00 Of cast iron2%
• Of steel
• 8481.80.73.10 For use in certain types of aircraft2%
• 8481.80.73.20 Pressure- and flow-control valve controlled by external electromagnet: - made of steel and/or steel alloy(s), - without integrated circuit, - of not more than 1000 kpa operating pressure, - with a flow quantity of not more than 5 l/min, - without an electromagnet2%
• 8481.80.73.90 Other2%
• Other
• 8481.80.79.10 For use in certain types of aircraft2%
• 8481.80.79.40 Service valve which suits for r410a or r32 gas while connecting indoor and outdoor units with: -a withstanding pressure of the valve body of 6,3 mpa, -a leakage ratio of less than 1.6 g/a, -an impurity ratio of less than 1.2 mg/pcs, -an airtight pressure of the valve body of 4.2 mpa for use in the manufacture of air conditioners2%
• 8481.80.79.90 Other2%
• Ball and plug valves
• 8481.80.81.30 For use in certain types of aircraft2%
• 8481.80.81.90 Other2%
• Butterfly valves
• 8481.80.85.30 For use in certain types of aircraft2%
• 8481.80.85.90 Other2%
• Diaphragm valves
• 8481.80.87.30 For use in certain types of aircraft2%
• 8481.80.87.90 Other2%
• Other
• 8481.80.99.40 For use in certain types of aircraft2%
• 8481.80.99.70 Pressure- and flow-control valve controlled by external electromagnet: - made of steel and/or steel alloy(s), - without integrated circuit, - of not more than 1000 kpa operating pressure, - with a flow quantity of not more than 5 l/min, - without an electromagnet2%
• 8481.80.99.80 Solenoid valve for combustion engine continuous variable valve timing system to control oil flow as a function of engine speed and load: -in metal cover, -with electrical connector, -with a force of not more than 10 n, -with an operating voltage of 9 vdc or more but not more than 16 vdc, -with a length of 80 mm or more but not more than 110 mm, -with a width of 80 mm or more but not more than 110 mm, -with a height of 20 mm or more but not more than 30 mm, for use in the manufacture of engines of motor vehicles2%
• 8481.80.99.90 Other2%

8481.90 Taps, cocks, valves and similar appliances; parts thereof

• 8481.90.00.10 For use in certain types of aircraft2%
• 8481.90.00.25 Die-cast aluminium housing for electronic throttle control or exhaust gas recirculation systems, comprising the following features: -high-pressure die-cast aluminium en ac-46000, -shot-blasted and machined, -height of 100 mm or more but not exceeding 135 mm, -width of 115 mm or more but not exceeding 150 mm, -weight of 210 g or more but not more than 500 g2%
• 8481.90.00.40 Valve armature: - for the opening and closing of the flow of fuel, - consisting of a shaft and a blade, - with at least 3 but not more than 8 holes on the blade, - made of metal and/or metal alloy(s)2%
• 8481.90.00.50 Silicone or plastic keyboards, comprising: -parts of common metal, and -whether or not comprising parts of plastic, -epoxy resin reinforced with fiberglass or wood, -whether or not printed or surface-treated, -with or without electrical conductors, -with or without a membrane bonded to the keyboard, -with or without mono or multilayer protective film2%
• 8481.90.00.60 Nozzle body for the regulation of angle and distribution of fuel injection: -of a cylindrical shape, -made of stainless steel, -with 4 or more, but not more than 16 holes, -with a flow rate of 100 cm³/minute or more, but not more than 500 cm³/minute2%
• 8481.90.00.70 Nozzle needle for opening and closing the flow of fuel in the engine, with: -2 holes, -4 grooves, -a diameter of 3 mm or more, but not more than 6 mm, -a length of 25 mm or more, but not more than 35 mm, -made of stainless steel with hard-chrome plating2%
• 8481.90.00.80 Flow-control valve -made of steel, -with an outlet hole with a diameter of at least 0,05 mm, but not more than 0,5 mm, -with an inlet hole with a diameter of at least 0,1 mm, but not more than 1,3 mm2%
• 8481.90.00.90 Other2%