8481 Taps, cocks, valves and similar appliances for pipes, boiler shells, tanks, vats or the like, including pressure-reducing valves and thermostatically controlled valves

8481.10 Valves; pressure reducing, for pipes, boiler shells, tanks, vats or the like

• Combined with filters or lubricators
• 8481.10.05.10 For use in certain types of aircraft2.2%
• 8481.10.05.90 Other2.2%
• Other
• Of cast iron or of steel
• 8481.10.19.10 For use in certain types of aircraft2.2%
• 8481.10.19.90 Other2.2%
• Other
• 8481.10.99.10 For use in certain types of aircraft2.2%
• 8481.10.99.40 Pressure reducing valves in a brass case with: a length of not more than 30 mm (± 1 mm); a width of not more than 18 mm (± 1 mm); of a kind used for incorporation in fuel delivery modules of motor vehicles2.2%
• 8481.10.99.90 Other2.2%

8481.20 Valves; for oleohydraulic or pneumatic transmissions

• Valves for the control of oleohydraulic power transmission
• 8481.20.10.20 For use in certain types of aircraft2.2%
• 8481.20.10.90 Other2.2%
• Valves for the control of pneumatic power transmission
• 8481.20.90.20 For use in certain types of aircraft2.2%
• 8481.20.90.90 Other2.2%

8481.30 Valves; check (nonreturn) valves, for pipes, boiler shells, tanks, vats or the like

• Of cast iron or of steel
• 8481.30.91.20 For use in certain types of aircraft2.2%
• Other
• 8481.30.91.30 Mechanical check (non-return) valve for opening and closing of the flow of fuel: with an operating pressure of not more than 250 MPa; with a flow rate of 45 cm³/minute or more, but not more than 55 cm³/minute; with 4 input holes, each of them with a diameter of 1,2 mm or more, but not more than 1,6 mm; made of steel2.2%
• 8481.30.91.91 Steel check (non-return) valves with: an opening pressure of not more than 800 kPa; an external diameter not more than 37 mm2.2%
• 8481.30.91.99 Other2.2%
• Other
• 8481.30.99.20 For use in certain types of aircraft2.2%
• 8481.30.99.50 Mechanical check (non-return) valve for opening and closing of the flow of fuel: with an operating pressure of not more than 250 MPa; with a flow rate of 45 cm³/minute or more, but not more than 55 cm³/minute; with 4 input holes, each of them with a diameter of 1,2 mm or more, but not more than 1,6 mm; made of steel2.2%
• 8481.30.99.90 Other2.2%

8481.40 Valves; safety or relief valves, for pipes, boiler shells, tanks, vats or the like

• Of cast iron or of steel
• 8481.40.10.50 For use in certain types of aircraft2.2%
• 8481.40.10.90 Other2.2%
• Other
• 8481.40.90.10 For use in certain types of aircraft2.2%
• 8481.40.90.90 Other2.2%

8481.80 Taps, cocks, valves and similar appliances; for pipes, boiler shells, tanks, vats or the like, including thermostatically controlled valves

• Taps, cocks and valves for sinks, washbasins, bidets, water cisterns, baths and similar fixtures
• Mixing valves
• 8481.80.11.10 For use in certain types of aircraft2.2%
• 8481.80.11.90 Other2.2%
• Other
• 8481.80.19.10 For use in certain types of aircraft2.2%
• 8481.80.19.90 Other2.2%
• Central heating radiator valves
• 8481.80.31.00 Thermostatic valves2.2%
• 8481.80.39.00 Other2.2%
• Valves for pneumatic tyres and inner tubes
• 8481.80.40.10 For use in certain types of aircraft2.2%
• 8481.80.40.90 Other2.2%
• Other
• Process control valves
• 8481.80.51.00 Temperature regulators2.2%
• Other
• 8481.80.59.20 Pressure regulating valve for incorporation into compressors of motor vehicle air condition units2.2%
• 8481.80.59.30 Two-way flow control valve with housing, with: at least 5, but not more than 16 outlet holes with at least 0,05 mm, but not more than 0,5 mm diameter; at least 330 cm³/minute, but not more than 5 000 cm³/minute flow rate; at least 19, but not more than 300 MPa operating pressure2.2%
• 8481.80.59.40 Flow-control valve: made of steel; with an outlet hole with a diameter of at least 0,05mm or more, but not more than 0,5 mm; with an inlet hole with a diameter of at least 0,1 mm, but not more than 1,3 mm; with chromium nitride coating; with a surface roughness of Rp 0,42.2%
• 8481.80.59.50 Electromagnetic valve for quantity control with: a plunger; a solenoid with a of coil resistance of at least 1,85 Ohm, but not more than 8,2 Ohm2.2%
• 8481.80.59.60 Electromagnetic valve for quantity control: with a solenoid with a coil resistance of at least 0,19 Ohm, but not more than 0,66 Ohm, and with an inductance of not more than 1 mH2.2%
• 8481.80.59.70 Flow-control valve: made of steel; with an outlet hole with a diameter of at least 0,05 mm, but not more than 0,5 mm; with an inlet hole with a diameter of at least 0,1 mm, but not more than 1,3 mm2.2%
• 8481.80.59.80 Solenoid valve for combustion engine oil pump to regulate the quantity of oil in the pump: with a cable of length of 550 mm or more but not more than 700 mm incorporating an electrical connector; with an operating pressure of not more than 5.5 bar; with an operating voltage of 9 VDC or more but not more than 16 VDC; with a valve's base width of 22 mm or more but not more than 27 mm; with a valve's length of 55 mm or more but not more than 110 mm; for use in the manufacture of motor vehicle engines2.2%
• 8481.80.59.90 Other2.2%
• Other
• Gate valves
• 8481.80.61.00 Of cast iron2.2%
• Of steel
• 8481.80.63.50 For use in certain types of aircraft2.2%
• 8481.80.63.90 Other2.2%
• Other
• 8481.80.69.50 For use in certain types of aircraft2.2%
• Other
• 8481.80.69.60 Four-way reversing valve for refrigerants, consisting of: a solenoid pilot valve; a brass valve body including valve slider and copper connections; with a working pressure up to 4,5 MPa2.2%
• 8481.80.69.99 Other2.2%
• Globe valves
• 8481.80.71.00 Of cast iron2.2%
• Of steel
• 8481.80.73.10 For use in certain types of aircraft2.2%
• 8481.80.73.20 Pressure- and flow-control valve controlled by external electromagnet: made of steel and/or steel alloy(s); without integrated circuit; of not more than 1000 kPa operating pressure; with a flow quantity of not more than 5 l/min; without an electromagnet2.2%
• 8481.80.73.90 Other2.2%
• Other
• 8481.80.79.10 For use in certain types of aircraft2.2%
• 8481.80.79.40 Service valve which suits for R410A or R32 gas while connecting indoor and outdoor units with: a withstanding pressure of the valve body of 6,3 MPa; a leakage ratio of less than 1.6 g/a; an impurity ratio of less than 1.2 mg/PCS; an airtight pressure of the valve body of 4.2 Mpa; for use in the manufacture of air conditioners2.2%
• 8481.80.79.90 Other2.2%
• Ball and plug valves
• 8481.80.81.30 For use in certain types of aircraft2.2%
• 8481.80.81.90 Other2.2%
• Butterfly valves
• 8481.80.85.30 For use in certain types of aircraft2.2%
• 8481.80.85.90 Other2.2%
• Diaphragm valves
• 8481.80.87.30 For use in certain types of aircraft2.2%
• 8481.80.87.90 Other2.2%
• Other
• 8481.80.99.40 For use in certain types of aircraft2.2%
• 8481.80.99.70 Pressure- and flow-control valve controlled by external electromagnet: made of steel and/or steel alloy(s); without integrated circuit; of not more than 1000 kPa operating pressure; with a flow quantity of not more than 5 l/min; without an electromagnet2.2%
• 8481.80.99.80 Solenoid valve for combustion engine continuous variable valve timing system to control oil flow as a function of engine speed and load: in metal cover; with electrical connector; with a force of not more than 10 N; with an operating voltage of 9 VDC or more but not more than 16 VDC; with a length of 80 mm or more but not more than 110 mm; with a width of 80 mm or more but not more than 110 mm; with a height of 20 mm or more but not more than 30 mm; for use in the manufacture of engines of motor vehicles2.2%
• 8481.80.99.90 Other2.2%

8481.90 Taps, cocks, valves and similar appliances; parts thereof

• 8481.90.00.10 For use in certain types of aircraft2.2%
• 8481.90.00.25 Die-cast aluminium housing for electronic throttle control or exhaust gas recirculation systems, comprising the following features: high-pressure die-cast aluminium EN AC-46000; shot-blasted and machined; height of 100 mm or more but not exceeding 135 mm; width of 115 mm or more but not exceeding 150 mm; weight of 210 g or more but not more than 500 g2.2%
• 8481.90.00.40 Valve armature: for the opening and closing of the flow of fuel; consisting of a shaft and a blade; with at least 3 but not more than 8 holes on the blade; made of metal and/or metal alloy(s)2.2%
• 8481.90.00.50 Silicone or plastic keyboards, comprising: parts of common metal, and whether or not comprising parts of plastic; epoxy resin reinforced with fiberglass or wood; whether or not printed or surface-treated; with or without electrical conductors; with or without a membrane bonded to the keyboard; with or without mono or multilayer protective film2.2%
• 8481.90.00.60 Nozzle body for the regulation of angle and distribution of fuel injection: of a cylindrical shape; made of stainless steel; with 4 or more, but not more than 16 holes; with a flow rate of 100 cm³/minute or more, but not more than 500 cm³/minute2.2%
• 8481.90.00.70 Nozzle needle for opening and closing the flow of fuel in the engine, with: -2 holes; -4 grooves: a diameter of 3 mm or more, but not more than 6 mm; a length of 25 mm or more, but not more than 35 mm; made of stainless steel with hard-chrome plating2.2%
• 8481.90.00.80 Flow-control valve: made of steel; with an outlet hole with a diameter of at least 0,05 mm, but not more than 0,5 mm; with an inlet hole with a diameter of at least 0,1 mm, but not more than 1,3 mm2.2%
• 8481.90.00.90 Other2.2%